Speaka Professional 1375412 Mode D'emploi page 3

Mobile headphones amplifier
Item no. 1375412
Intended use
The headphones amplifier is designed to amplify an audio signal and transmit it to a pair of
headphones. The inputs and outputs must only be connected to sockets on audio devices.
Headphones must be connected with a 3.5 mm jack plug. Power is supplied via the built-in
rechargeable battery, which can be charged via a standard USB port. The product cannot be
operated with another power supply.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Mobile headphones amplifier
• 3.5 mm 4-pole to 3.5 mm 4-pole cable
• Micro USB cable
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
• Do not place the product under any mechanical stress.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Do not listen to excessively loud music over an extended period of time. This may damage
your hearing.
• Never use the product immediately after it has been brought from a cold room into a warm
one. The condensation generated could destroy the product. Allow the product to reach room
temperature before connecting it to the power supply and putting it to use. This may take
several hours.
• Only use the product in temperate climates, not in tropical climates.
• Do not leave the product unattended while in operation.
• Check the product for damage from time to time.
• Turn off all audio signal sources and set their volume to zero. Turn the volume control knob
anticlockwise as far as it will go to turn off the amplifier before connecting the headphones.
• Before connecting the headphones, turn off all devices that you are going to connect to the
headphones amplifier and disconnect them from the power supply. Follow the same steps
when making changes to the connections.
• Do not place any open flames (e.g. burning candles) on or near the headphones amplifier.
b) Rechargeable battery
• The rechargeable battery is permanently built into the product and cannot be replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable battery
Version 10/15
might cause an explosion or a fire! Unlike conventional batteries/rechargeable batteries (e.g.
AA or AAA type), the casing of the LiPo rechargeable battery does not consist of a thin sheet
but rather a sensitive plastic film only.
• Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the
product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you are not using the product. Due to the
rechargeable battery technology being used, you do not need to discharge the rechargeable
battery first.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is normal that a
certain amount of heat is generated during charging.
c) Miscellaneous
• In industrial facilities, the accident prevention regulations for electrical equipment and
facilities issued by the Industrial Employers' Liability Association must be adhered to!
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at
a qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating elements
1
Operation
a) Charging the battery
• The multifunctional LED (4) flashes when the battery level is low. The battery should then
be charged.
• Ensure that you fully charge the battery before using the product for the first time.
• Connect the micro USB port (7) to a suitable USB power source using the micro USB cable
(included with the product). The red LED turns on when the amplifier is connected to a USB
port and turned off (at the volume control knob (3)). This indicates that the battery is charging.
The LED alternates between blue and red when the product is turned on and the battery is
charging.
• A full charging cycle takes approximately 1 hour. The red LED turns off when the amplifier is
turned off; it turns blue when the amplifier is turned on.
• Disconnect the USB power supply from the amplifier when the battery is fully charged.
1 Audio output 1 (3.5 mm jack socket)
2 Audio output 2 (3.5 mm jack socket)
4 3 Volume knob with on/off switch
4 Multifunctional LED
5 Selector switch (bass level)
6 Audio input (3.5 mm jack socket)
7 Micro USB port
2 3 5 6 7