Making Connections; Switching On/Off; Muting The Output; Monitor Output - JTS CX-500DUSET Mode D'emploi

3.5 Making connections

Before connecting /disconnecting, mute the
input or turn down the volume of the corre-
sponding device (e. g. mixing console or am-
plifier).
1) Connect the mini XLR plugs of the two micro-
phones to the jacks IN L (1) and IN R (3). The
plug will be locked; to remove the plug later,
press the button on the side of the plug to
unlock it.
2) Use an XLR cable to connect the output (2)
of the mixer to the input of the subsequent
device (e. g. mixing console or amplifier).
4 Operation
4.1 Switching on / off
The switch PHANTOM / BATTERY (5) to select
the power supply can also be used to switch
the mixer on and off.
Important: To prevent loud switching noise, only use
this switch when the input at the device connected
(e. g. mixing console or amplifier) has been muted or
when the volume has been turned down.
Battery operation: To switch the mixer
on, set the switch to the position BATTERY.
Usually, the LED (8) is green; if it is red, the bat-
tery is low and should be replaced (
ter 3.2). After operation, set the switch to the
position PHANTOM to save the battery.
Phantom power supply: To switch the mixer
on, set the switch to the position PHANTOM.
The LED (8) is green when phantom power is
available. In the position BATTERY, the mixer
will remain switched off when no battery has
been inserted.

4.2 Muting the output

In the position ON of the switch ON / MUTE (7),
the sound at the output (2) of the mixer is
activated.
To mute the output [e. g. to tune the in-
strument or to monitor the mixed signal via
the monitor output (12)], set the switch to
the position MUTE.
Vertrieb von JTS-Produkten – Distribution of JTS products
➄
4.3 Mixing signals
Each microphone input has its own volume
control: Use the control VOL L (4) to adjust the
volume of the microphone at the input IN L (1)
and the control VOL R (6) to adjust the volume
of the microphone at the input IN R (3).
chap-
☞

4.4 Monitor output

To monitor the mixed signal, stereo head-
phones with a 3.5 mm plug can be connected
to the jack (12). This function is only avail-
able for battery operation. The mixed signal is
monophonic and can only be heard when the
switch ON / MUTE (7) is in the position MUTE.
Adjust the headphone volume via the con-
trol VOL (9) on the rear of the mixer using
a small screwdriver.
CAUTION
Never adjust a very high volume.
Permanent high volumes may dam-
age your hearing!
Note: The volume of the monitor output also de-
pends on the position of the switch LINE / MIC. (13).
®
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen, Germany
Copyright © by MONACOR INTERNATIONAL. All rights reserved.
6
10
VOL R
12
5 Specifications
Miniature microphone
System: . . . . . . . . . . . . . back electret
Pick-up pattern: . . . . . . omnidirectional
Frequency range: . . . . . 20 – 20 000 Hz
Nominal impedance: . . . 1.5 kΩ
Sensitivity: . . . . . . . . . . . 12.6 mV/ Pa
S / N ratio: . . . . . . . . . . . ≥ 68 dB
Max. SPL: . . . . . . . . . . . 130 dB
Dimensions: . . . . . . . . . ⌀ 6 mm × 13 mm
Weight: . . . . . . . . . . . . 6.5 g
(including cable)
Power supply: . . . . . . . . ⎓ 1– 5 V
(via PS-510M)
Mixer / Power supply PS-510M
Inputs: . . . . . . . . . . . . . 5 kΩ, mini XLR,
unbalanced
Output: . . . . . . . . . . . . . 470 Ω, XLR,
balanced
Power supply: . . . . . . . . battery (9 V) or
phantom power
12 – 48 V
Max. power
consumption: . . . . . . . . 80 mA (with head-
phones)
Dimensions: . . . . . . . . . 65 × 92 × 30 mm
Weight: . . . . . . . . . . . . 81 g
Pin configuration
Microphone inputs (1, 3), mini XLR
1
1 3
4
supply voltage for the
2
2
3 = 4 microphone signal
Output (2), XLR
1
1 2
2
3
3
Monitor output (12), 3.5 mm plug
T mixed signal (mono)
T R S
R mixed signal (mono)
S
Subject to technical modification.
A-2059.99.01.06.2020
ground
microphone
ground
signal +
signal −
ground