Uline H-2771 Guide Rapide
  1. Manuels
  2. Marques
  3. Uline Manuels
  4. Équipement industriel
  5. H-2771
  6. Guide rapide
Uline H-2771 Guide Rapide

Uline H-2771 Guide Rapide

Masquer les pouces
1
2
3
4
5
6
7
8
9
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
H-2771, H-2772, H-2773, H-2774
H-2775, H-2776, H-5242, H-5243
FORKLIFT AERIAL PLATFORM
AND ACCESSORIES
TOOL NEEDED
1/2" Wrench
1.
Inspect each unit when received for damage
incurred during shipping. Inspect prior to each
use for any damage, unusual wear, deterioration,
corrosion or missing or loose components.
2. Do not use units that are damaged, weakened or
are missing parts for any reason until repairs are
completed. Units that are damaged, after their
arrival, and/or are worn beyond repair, should be
destroyed. Never use a damaged platform.
1.
Insert handrail assemblies evenly and all the way
to the bottom of the corner pipe sockets. Install
handrail assemblies in the correct direction. Holes
in handrails will be towards rear. The gate will be on
front of platform, as user enters, with gate facing in.
The handrail assemblies have a snug fit and may
require a slight tapping to get them to the bottom of
the sockets. Install one 5/16-18 x 3/4" long bolt into
each of the corner pipe sockets and tighten.
2. Position back screen so slots are on the sides. Place
screen between handrails so mesh side is facing into
platform. Align slots in screen with holes in handrails.
Fasten screen between handrails using 5/16-18 x 1½"
long bolts and locknuts.
3. The retainer chain installs between the two round
rings at back of platform. One end is pre-attached
to a ring. The other end will attach to opposite ring
using the snap hook, which is already attached to
end of chain.
4. The retainer chain is used to secure platform to fork
truck during use. Retainer chain spans behind mast
of fork truck and hooks to other ring. The retainer
chain must be used whenever platform is in use.
Unhook chain before removing platform from fork
truck.
PAGE 1 OF 9
1-800-295-5510
uline.com
SAFETY
3. Do not use the platform if the retainer chain or
anchor point is damaged or missing.
4. A defaced or missing label should be replaced.
Contact Uline Customer Service at 1-800-295-5510.
5. Check all fasteners and tighten if necessary.
6. Review all safety capacity labels.
ASSEMBLY
Support Arm*
5/16-18 x 1½"
Bolt with Nut
Clamp*
5/16-18 x 3/4"
Gate
Locknut
Fork
Pockets
5/16-18 x 3/4" Bolt
* Items are included with H-5242 and H-5243 Screen Risers.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Bolt
Swivel Caster
Riser
Screen*
5/16-18 x 3/4"
Bolt with Nut*
Back Screen
Anchor
Point
Retainer
Chain
0921 IH-2771

Publicité

Table des Matières
loading

Manuels Connexes pour Uline H-2771

Sommaire des Matières pour Uline H-2771

  • Page 1 4. A defaced or missing label should be replaced. corrosion or missing or loose components. Contact Uline Customer Service at 1-800-295-5510. 2. Do not use units that are damaged, weakened or 5. Check all fasteners and tighten if necessary.

  • Page 2: Accessories

    OPERATION • Units are intended for use on level surfaces. • When occupied, the access opening must be with either the latched gate or gate chains. Verify the • Users are cautioned to take proper safety measures gate latch or chains are properly secured. when units are used in areas containing electrical circuits.
  • Page 3 NOTE: Ensure riser is completely upright when attaching the clamp and support arms. Hardware Included Clamp Clamp x 2 Washer x 7 Back Screen 5/16-18 x 3/4" Bolt x 7 Locknut x 7 1-800-295-5510 uline.com PAGE 3 OF 9 0921 IH-2771...

  • Page 4: Herramienta Necesaria

    H-2771, H-2772, H-2773, H-2774 800-295-5510 H-2775, H-2776, H-5242, H-5243 uline.mx PLATAFORMA DE TRABAJO PARA MONTACARGAS Y ACCESORIOS HERRAMIENTA NECESARIA Llave de 1/2" SEGURIDAD Inspeccione cada unidad cuando la reciba para 3. No utilice una plataforma si la cadena de retención verificar que no haya sufrido daños durante el...
  • Page 5 CONTINUACIÓN DE ENSAMBLE 4. La cadena de retención se usa para asegurar la La cadena de retención debe usarse siempre que plataforma elevadora al montacargas durante su la plataforma esté en uso. Desenganche la cadena uso. La cadena de retención se extiende desde antes de retirar la plataforma del montacargas.
  • Page 6 NOTA: Asegúrese de que la pantalla esté completamente en posición vertical cuando coloque la abrazadera y los brazos de soporte. Tornillería Incluida Abrazadera Pantalla Posterior 2 Abrazaderas 7 Rondanas 7 Pernos de 5/16-18 x 3/4" 7 Contratuercas 800-295-5510 uline.mx PAGE 6 OF 9 0921 IH-2771...

  • Page 7: Plateforme Élévatrice De Chariot Élévateur Et Accessoires

    H-2771, H-2772, H-2773, H-2774 1-800-295-5510 H-2775, H-2776, H-5242, H-5243 uline.ca PLATEFORME ÉLÉVATRICE DE CHARIOT ÉLÉVATEUR ET ACCESSOIRES OUTIL REQUIS Clé de 1/2 po SÉCURITÉ 1. Vérifiez chaque unité à sa réception pour détecter 3. N'utilisez pas la plateforme si la chaîne de retenue les dommages subis pendant le transport.

  • Page 8: Assemblage Suite

    ASSEMBLAGE SUITE 4. La chaîne de retenue est utilisée pour fixer la La chaîne de retenue doit être utilisée chaque fois plateforme élévatrice au chariot élévateur pendant que vous utilisez la plateforme. Décrochez la chaîne l'utilisation. La chaîne de retenue passe derrière avant de retirer la plateforme du chariot élévateur.

  • Page 9: Accessoires

    élévatrice. Fixez à l'aide de trois boulons 5/16-18 x Attache x 2 Rondelle x 7 3/4 po, des rondelles et des écrous freiné. (Voir Figure 3A) Boulon 5/16-18 x 3/4 po x 7 Écrou freiné x 7 1-800-295-5510 uline.ca PAGE 9 OF 9 0921 IH-2771...

Ce manuel est également adapté pour:

H-2772H-2773H-2774H-2775H-2776H-5242 ... Afficher tout

Table des Matières