Settings Mode; Temperature Display - AIRLUX ARCAV54 Manuel D'instructions


You can press the left side UP and DOWN keys
to control the internal temperature of the
UPPER temperature zone and press the right
side UP and DOWN keys to control the internal
temperature of the LOWER temperature zone.
When you press the two keys at the first time,
the display will show the last temperature set
previously.
NOTE: The temperature
LOWER/RIGHT temperature zone must always
be just as high or higher than that in the
UPPER/LEFT temperature zone. For optimal
performance, the set temperature of the two
zones should differ by at least 4° C.

The temperature that you desire to set will
increase 1º C or 1º F if you press the UP mark
once, on the contrary the temperature will
decrease 1º C or 1º F if you press the DOWN
mark once. The display flashes while you make
the setting.

After the temperature has been set, the display
shows the current inner temperature of the
particular temperature zone.

To view the set temperature at any time, press
the UP or DOWN key, the set temperature will
temporarily flash in the display for 5 seconds.
Then the display shows the current inner
temperature again.

SETTINGS MODE

Certain settings on the wine cabinet can only be
selected in settings mode. In settings mode only the
UP and DOWN keys of lower/right zone are valid for
dual zone and three zone LED display units.
º F/º C Selection
▪ Lightly touch and hold the UP key for 5 seconds.
▪ Use the UP and DOWN keys to select the
temperature display setting in Fahrenheit or
Celsius degree.
▪ Touch the POWER key to confirm your selection.
▪ Touch and hold the UP key for 5 seconds to leave
settings mode. Otherwise the appliance exits
settings mode automatically after approximately
one minute.
Display Brightness
▪ Lightly touch and hold the UP key for 5 seconds
and then touch the POWER key once.
▪ Use the UP and DOWN keys to select the
brightness of the display. The factory default
setting is d1.
d1: dimmest setting
d2: medium setting
d3: brightest setting
▪ Touch the POWER key to confirm your selection.
▪ Touch and hold the UP key for 5 seconds to leave
settings mode. Otherwise the appliance exits
set for the
30
settings mode automatically after approximately
one minute.
Interior Lighting Brightness
▪ Lightly touch and hold the UP key for 5 seconds
and then touch the POWER key twice.
▪ Use the UP and DOWN keys to select the
brightness of the interior lighting. The factory
default setting is L3.
L1: dimmest setting
L2: medium setting
L3: brightest setting
▪ Touch the POWER key to confirm your selection.
▪ Touch and hold the UP key for 5 seconds to leave
settings mode. Otherwise the appliance exits
settings mode automatically after approximately
one minute.
Fan Mode
▪ Lightly touch and hold the UP key for 5 seconds
and then touch the POWER key three times.
▪ Use the UP and DOWN keys to select the fan
mode. The factory default setting is F0.
F0: Silent mode - Energy saving mode
F1: DynaClima mode - half time
F2: DynaClima mode - full time
▪ Touch the POWER key to confirm your selection.
▪ Touch and hold the UP key for 5 seconds to leave
settings mode. Otherwise the appliance exits
settings mode automatically after approximately
one minute.
Audible Tones
▪ Lightly touch and hold the UP key for 5 seconds
and then touch the POWER key four times.
▪ Use the UP and DOWN keys to select the audible
tones. The factory default setting is S1.
S0: sensor tone ON, alarm tone OFF
S1: sensor tone ON, alarm tone ON
S2: sensor tone OFF, alarm tone OFF
S3: sensor tone OFF, alarm tone ON
▪ Touch the POWER key to confirm your selection.
▪ Touch and hold the UP key for 5 seconds to leave
settings mode. Otherwise the appliance exits
settings mode automatically after approximately
one minute.

TEMPERATURE DISPLAY

During normal operation, the temperature display on
the control panel shows the temperature inside the
appliance. The temperature display will flash if
- A different temperature is being set,
- The temperature in the zone deviates by more
than 5° C from the set temperature.
The temperature display flashing ensures that the
temperature can not rise or fall un-noticed and
impair the wine.