Bell & Ross BR 05 Artline Notice Technique page 3

ENGLISH
BR 05 ARTLINE
LTD 250 PCS
BR-CAL.321
Movement : mechanical with automatic winding. Calibre BR-CAL.321. Power reserve approximately 40 hours.
: 40 mm in width.
Case
GENERAL USE
0 1
Starting the watch
When the watch has stopped (crown in position 0): unscrew the crown
(turn anticlockwise) to position 1. Wind the movement by turning the
0 1
crown clockwise. After approximately 40 rotations, the watch is fully
wound (the winding mechanism does not have a stop to prevent over-
winding). The power reserve is approximately 40 hours when fully
wound. When the watch is worn , the automatic mechanism will wind
the movement.
resistance, screw the crown back into position 0. Never operate the
crown underwater.
Setting the time
0 1 2 3
Unscrew the crown then pull it out to position 3. The seconds hand
will stop, enabling the time to be set to the nearest second. Set the
time by rotating the crown in the required direction.
0 1 2 3
IMPORTANT
. Magnetic fields can adversely affect the accuracy of your watch. Also, we would
Magnetic fields
recommend that you avoid placing your watch near electronic devices that may generate large
magnetic fields (radio, smartphone, television, computer, tablet, loudspeakers, etc.).
: the slotted screws mount the bezel to the case and ensure the water resistance of the
NOTE
watch. To benefit from the Bell & Ross warranty, these screws must never be unscrewed.
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the watch and strap with
fresh water. It is also recommended to have the water resistance of your watch checked every two
years. To ensure a service that meets the brand's exacting standards, any servicing of your watch
must be carried out by the Bell & Ross service centre or a watchmaker approved by Bell & Ross.
Whenever repairs are made during the warranty period, you must present the Bell & Ross warranty
card, duly dated and signed by the retailer at the time the watch was purchased.
0 1 2
0 1 2
0 1
: Once the watch is set, to ensure perfect water
NOTE
0 1 2
0 1 2 3
0 1 2
Minute hand
Hour hand
Seconds hand
Functions : hours, minutes and seconds. Date with quickset. Time-setting with hacking function.
0 1
Setting the date
Quick setting
Crown in position 2: unscrew and pull the crown out to position 2 and
0 1 2
set the date by turning the crown anticlockwise.
mechanical watches with a date function, quickset date setting MUST
NOT UNDER ANY CIRCUMSTANCES be carried out between the times
of 9 PM (21.00) and 3 AM (3.00).
Slow setting
Crown in position 3: to ensure the date changes at midnight rather
0 1 2 3
than noon, it is recommended to set the date by adjusting the hands of
the watch. Unscrew and pull the crown out to position 3 and turn the
hands until the date changes. Then set the precise time.
0 1 2
INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated at the time of
purchase by your approved Bell & Ross point of sale, and presented every time an operation is
performed. You can now access the digital version of this card and all the information relating to
your watch by scanning the QR code or visiting:
To ensure a service that meets the brand's exacting standards, any servicing of your watch must
be carried out by the Bell & Ross service centre or a watchmaker approved by Bell & Ross. The
warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the watch (e.g. violent
impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer or after-sales
service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and tear.
3
0 1 2
NOTE
0 1 2
Date
Crown
Case attachment screw
(NEVER UNSCREW)
www.bellross.com/warranty.
: as with all