Watching A Tv Program; Power; Volume; Channel Selection - Sharp 13VT-CR10 Mode D'emploi

Watching A TV Program

1 POWER

• Press the POWER button to turn on the TV.
(The POWER indicator will be lit in RED.)
Sound will start instantly and picture will appear 5 to 10
seconds later.
• Press the POWER button again to turn off the TV.
(The POWER indicator will be turned off.)

2 VOLUME

• Press the VOL UP (8) button to increase the sound to the
desired level, and then release.
• Press the VOL DOWN (9) button to decrease the sound
level.
L To turn the sound off temporarily
• Press the MUTE button on the Remote Control to turn the
sound off.
"MUTE" will appear on the screen to confirm that this fea-
ture is in effect.
• Press the MUTE button again to restore the sound to its
previous level.

3 CHANNEL SELECTION

• The desired channel can be selected instantly by press-
ing the CHANNEL SELECT buttons (0 ~ 9, 100) on the
Remote Control, or CHANNEL UP (8)/DOWN (9) but-
tons on the Remote Control or on the TV.
• To select cable channel numbers greater than " 99 ". First
press " 100 " button on the Remote Control; then the two
other numbers buttons to complete your total channel
number selection.
• The selected channel number will appear on the screen.
Example:
(1) To select channel 2 :
Press the " 0 " and " 2 " buttons.
To select channel 69 :
Press the " 6 " and " 9 " buttons.
To select channel 125 (CATV mode only) :
Press the " 100 ", " 2 " and " 5 " buttons.
(2) The memorized channel selection will change in sequence
from the low preset channel to the high preset channel
when the CH UP (8) button is pressed, and vice versa
when the CH DOWN (9) button is pressed after you pre-
set the desired channels into the memory.
Note:
• For channel memory, please refer to page 11.

4 DISPLAY CALL

• Pressing the DISPLAY button on the Remote Control will
change the display on the screen in the following sequence.
Note:
• When CLOSED CAPTION is turned ON, the ON SCREEN
DISPLAY turns off automatically after about 3 seconds.
• For CLOSED CAPTION information, please refer to
pages 9 ~ 10.
05-07 13VT-CR10[E].pm65e
Downloaded from: http://www.usersmanualguide.com/
7
Press Once* • Time and Date
• Channel Number
• (Tape Operation Display)
• (Tape Speed Mode — SP, LP, EP)
• (Tape Counter)
After about 3 • Channel Number
seconds • (Tape Operation Display)
• (Tape Speed Mode — SP, LP, EP)
• (Tape Counter)
Press Twice • Cleans Display
Items in ( ) will be displayed when a cassette is loaded in the
VCR.

5 MENU FUNCTIONS

L Calling up the Functions
(1) Press the MENU button on the Remote Control to call the
MENU screen.
(2) Press the + or – button on the Remote Control to select
the desired function mode. Each time that you press the +
or – button, the " :" mark moves down or up.
(3) Press the SET button on the Remote Control to access
desired function mode.
• To leave the MENU screen, press the MENU button on
the Remote Control.

6 TRILINGUAL ON SCREEN DISPLAY

L The language for this unit's ON SCREEN DISPLAY can
be set to ENGLISH, SPANISH or FRENCH.
L Setting the ON SCREEN DISPLAY Language
(1) Select "LANGUAGE" from
the MENU screen by
pressing + or – button,
then press the SET
button.
(2) Press the + or – button
to select the language
(English, Spanish or
French) you wish to
display, then press the
SET button.
15/5/01, 7:51 pm
DISPLAY
M E N U
T I M E R
V I D E O A D J U S T
C L O S E D C A P T I O N
F U N C T I O N
C L O C K
L A N G U A G E
C H S E T T I N G
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
(MENU screen)
M E N U
T I M E R
V I D E O A D J U S T
C L O S E D C A P T I O N
F U N C T I O N
C L O C K
L A N G U A G E
C H S E T T I N G
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
L A N G U A G E
E N G L I S H
E S P A N O L
F R A N C A I S
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
7