Sharp 13VT-CR10 Mode D'emploi page 19

Recording With The Timer (Continued)
L To confirm the program content, press the CONFIRM
button on the Remote Control.
L To add to the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select "NEXT", then
press the SET button.
(3) To add a program, follow
the steps (3) through (10)
of "Setting The Program
Timer".
L To change the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select "CHANGE", then
press the SET button.
(3) Press the + or – button
to select the program you
wish to correct, then press
the SET button.
To reset the program,
follow the steps (3)
through (10) of "Setting
The Program Timer".
L To delete the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select "DELETE", then
press the SET button.
(3) Press the + or – button
to select the program you
wish to delete, then press
the SET button.
(4) Press the CONFIRM
button to return to the
normal screen.
Note:
• During the Program Timer Setting (with the Program Timer
indicator ON), it is impossible to change or delete the
program content. To perform these operations, press the
TIMER ON/OFF button on the Remote Control and turn
off the Program Timer indicator.
16-19 13VT-CR10[E].pm65e
Downloaded from: http://www.usersmanualguide.com/
R E C T I M E R P R O G R A M
M O D E C H S T A R T S T O P
1 D A I L Y 8 2 4 : 3 0PM 6: 0 0 PM SP
2 M O N - F R I 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP
3 1 5 ( S A T ) 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
4
5
C O M P L E T E N E X T C H A N G E D E L E T E
1 0 : 2 0 A M O C T . 1 5 ( F R I )
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
R E C T I M E R P R O G R A M
M O D E C H S T A R T S T O P
1 D A I L Y 8 2 4 : 3 0PM 6: 0 0 PM SP
2 M O N - F R I 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP
3 1 5 ( S A T ) 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
4
5
C O M P L E T E N E X T C H A N G E D E L E T E
1 0 : 2 0 A M O C T . 1 5 ( F R I )
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
R E C T I M E R P R O G R A M
M O D E C H S T A R T S T O P
6: 0 0 PM SP
1 D A I L Y 8 2 4 : 3 0PM
2 M O N - F R I 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP
3 1 5 ( S A T ) 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
4
5
C O M P L E T E N E X T C H A N G E D E L E T E
S E L E C T P R O G R A M T O C H A N G E
1 0 : 2 0 A M O C T . 1 5 ( F R I )
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
R E C T I M E R P R O G R A M
M O D E C H S T A R T S T O P
1 D A I L Y 8 2 4 : 3 0PM 6: 0 0 PM SP
2 M O N - F R I 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP
3 1 5 ( S A T ) 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
4
5
C O M P L E T E N E X T C H A N G E D E L E T E
S E L E C T P R O G R A M T O D E L E T E
1 0 : 2 0 A M O C T . 1 5 ( F R I )
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
19
L Notes on the Timer Recording
• To correct any erroneous data entry made during program
timer setting work:
(1) Press the RETURN button on the Remote Control to
return to the item you wish to change.
(2) Press the + or – button on the Remote Control to reset
the data.
(3) To advance operation, press the SET button.
• If the video cassette runs out of tape before recording all
the programs, the VCR will stop, eject the cassette and
shut off automatically.
• If you keep disconnected the power cord, the program
timer will be cancelled.
• If "complete" is selected to enter the TIMER Standby mode
when there is no cassette inserted, the PROGRAM TIMER
indicator flashes for 3 seconds and the message "NO
TAPE" appears indicating that timer recording is not
possible.
• If "complete" is selected to enter the TIMER Standby mode
while a cassette with the erasure protection tab removed
is inserted, the PROGRAM TIMER indicator flashes and
the cassette is ejected.
• To stop timer recording, press the STOP button.
• If no buttons are pressed within 3 minutes while setting a
program, the set automatically returns to the normal
viewing mode.
• A program cannot be set unless all the recording input
data is set.
• During program timer setting (with the Program Timer
indicator ON), the video set remains inoperative. To use
the video set, press the TIMER ON/OFF button on the
Remote Control to turn off the Program Timer indicator.
After use, load the cassette tape into the video set, press
the TIMER ON/OFF button and check that the Program
Timer indicator lights up.
• Be certain that the correct TV signal mode (AIR/CABLE)
is selected before you enter the Timer Standby mode.
Otherwise, the VCR may not record the desired TV
channel.
• If two Pre-Recording Timers overlap, the End Recording
Time of the PROGRAM TIMER 1 will have priority over
the Start Recording Time of the PROGRAM TIMER 2.
Example:
Pre-Recording Timer's Interval
P R O G R A M T I M E R 1
7:00 8:00 8:30
Start Start End
Recording Recording Recording
Actual Recording Timer's Interval
End
Recording
P R O G R A M T I M E R 1
7:00 8:30
Start Start
Recording Recording
15/5/01, 7:25 pm
P R O G R A M T I M E R 2
10:00
End
Recording
P R O G R A M T I M E R 2
10:00
End
Recording
19