Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Fascia
Hitch Shown In Proper Position
Equipment Required: Pullwire (provided)
Fastener Kit: 24842F
Wrenches: 11/16, 9/16 & 10MM
Fastener are typical
For both sides
j
Carriage bolt – 7/16-14 X 1-1/2" GR 5
Qty. (6)
k
Qty. (6)
Spacer
l
Conical washer 7/16"
Qty. (6)
m
Qty. (6)
Hex nut 7/16-14
1.
Remove fascia tabs forward attachment fasteners.
2.
Use pull wires to feed the carriage bolts and blocks into frame rails though access holes as shown. Leave pull wire attached.
3.
Raise hitch into position over fascia tabs. Feed pull wires thru adjacent holes in the hitch, remove pull wires and attach conical
washers and nut finger tight only (Be careful not to push fastener back into frame rail). Hand tighten only until all fasteners are
installed.
4.
Install remaining fasteners as shown above.
5.
Torque all fasteners to specifications.
6.
Reattach fascia straps.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009, 2011 Cequent Performance Products
Installation Instructions
Mazda 3 4-Door
Drawbar Kit:
Drawbar must be used in the
RISE position only.
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
3594
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Access holes
Existing hole
Tie down hole
p q
Fascia
tabs
n
Qty. (2)
Hex bolt 3/8-16 X 2.00 GR5
o
Qty. (2)
Flat washer
p
Conical washer 3/8"
Qty. (2)
q
Qty. (2)
Hex nut 3/8-16
Sheet 1 of 3
24842N
Part Numbers:
24842
60258
77244
Manufacturer's Rating or
j
k
o n
l
m
5-26-11
Rev. C
Publicité
Manuels Connexes pour Cequent Performance Products 24842
Sommaire des Matières pour Cequent Performance Products 24842
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2009, 2011 Cequent Performance Products Sheet 1 of 3 24842N 5-26-11 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2009, 2011 Cequent Performance Products Feuille 2 de 3 24842N 5-26-11 Rev.
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2009, 2011 Cequent Performance Products Hoja 3 de 3 24842N 5-26-11 Rev.