Lutron D-600P Guide Rapide

Models:
English
Ariadni
Model Numbers:
Incandescent /
600 W
D-600P
Halogen
D-600R
D-603P
120 V~ Dimmer
DNG-600P
DNG-603P
Rated at 120 V~ 60 Hz 600 or DV-600P
DV-603P
1000 W (depending on model).
DVSC-600P
1. CAUTION: Use only with permanently-installed 120 V~
2. Install in accordance with all national and local electrical codes.
P/N 0301690 3. Only one dimmer can be used in a 3-way circuit.
4. When no "grounding means" exist within the wallbox then
• Easy-to-follow Instructions
• Instructions faciles à Suivre
5. For new installations, install a test switch before installing the
6. Protect dimmer from dust and dirt when painting or spackling.
7. Recommended minimum load is 40 W.
8. It is normal for the dimmer to feel warm to the touch during
9. Clean dimmer with a soft damp cloth only. Do not use any
Multigang Installations
When installing more than one control in the same wallbox,
it may be necessary to remove all inner side sections prior
to wiring (see below). If pre-installed, remove the Lutron
wallplate and wallplate adapter from dimmer. Using pliers,
bend side section up and down until they break off. Repeat
for each side section to be removed. Removal of dimmer
side sections reduces maximum load capacity. Refer to chart
below for maximum dimmer capacity.
Dimmer Capacity Chart
Dimmer Rating No sides removed
600 W 600 W
1000 W 1000 W
Technical Assistance
?
If you have questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when calling.
U.S.A. and Canada (24 hrs/7days)
+1.800.523.9466
Other countries 8am – 8pm ET
+1.610.282.3800
México
+1.888.235.2910
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to
place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU Of ALL OTHER ExPRESS WARRANTIES, AND THE IMPLIED WARRANTY Of MERCHANTABILITY IS LIMITED TO ONE YEAR fROM
PURCHASE. THIS WARRANTY DOES NOT COVER THE COST Of INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING fROM MISUSE, ABUSE,
OR DAMAGE fROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEqUENTIAL DAMAGES. LUTRON'S
LIABILITY ON ANY CLAIM fOR DAMAGES ARISING OUT Of OR IN CONNECTION WITH THE MANUfACTURE, SALE, INSTALLATION, DELIVERY, OR USE Of THE
UNIT SHALL NEVER ExCEED THE PURCHASE PRICE Of THE UNIT.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you.
Lutron, Ariadni, Claro, Diva, Fassada, Glyder, Luméa, and Skylark are registered trademarks and Luméa2 is a trademark of Lutron Electronics Co., Inc., NEC is a
registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
© 2013 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
P/N 0301690 Rev. A
, Diva , Glyder , Luméa2 , Rotary, Skylark
® ® ® ®
™
1000 W
DVSC-603P S-600 AY-10P DVW-10P S-103P
DVW-600P AY-10PNL DVW-103P S-103PNL
S-600P
DVW-603P S-600PG AY-103P GL-10P TG-10P
AY-103PNL GL-1000 TG-10PNL
GL-600 S-600PNL
GL-600P DV-10P GL-103P TG-103P
S-603P
GL-603P DV-103P S-10P
LG-600P DVSC-10P S-10PNL
LG-603P DVSC-103P S-1000
Important Notes
Please read before installing.
incandescent or halogen fixtures. To avoid overheating and
possible damage to other equipment, do not use to control
receptacles, fluorescent lighting fixtures, motor-driven
appliances, or transformer-supplied appliances.
NEC 2008, Article 404.9 allows a dimmer without a grounding
®
connection to be installed as a replacement, as long as a
plastic, noncombustible wallplate is used. For this type of
installation, cap or remove the green ground wire on the
dimmer and use an appropriate wallplate such as Lutron's
Claro or Fassada series wallplates.
® ®
dimmer.
operation.
chemical cleaners.
Do Not Remove
Outside Sections
Each Control Has Inside Middle Control Has Two Side
Sections Removed Sections Removed
1 side removed 2 sides removed
500 W 400 W
800 W 650 W
Fax +1.610.282.1243
http://www.lutron.com
Installation
1
Turning Off power.
• Turn power OFF at circuit breaker (or remove fuse).
WARNING: Shock Hazard. May result in serious
injury or death. Turn off power at
circuit breaker before installing
the unit.
2
Removing wallplate and switch.
• Remove wallplate and switch mounting screws.
• Carefully remove switch from wall (do not remove wires).
Caution: Verify power
is OFF to switch before
proceeding.
3
Identifying the type of circuit.
Different-colored screw
(Common). Actual location may
vary.
OR
Ground (Bare
Copper or
Green Wire)
Ground (Bare Copper
or Green Wire)
SINGLE-POLE: 3-WAY:
Insulated wires connected Insulated wires connected to three screws. One
to two screws of the same of these wires is connected to a screw of a
OR
color. Replace with a different-color (not green) or labeled COMMON.
MARK or TAG this wire to identify it when wiring.
SINGLE-POLE dimmer.
See Step 5a. Replace with a 3-WAY dimmer. See Step 5b.
4
Disconnecting switch wires.
• Carefully disconnect switch wires.
Screw Terminals:
Turn screws to
loosen.
Important Wiring Information
When making wire connections, follow the recommended strip lengths and
combinations for the supplied wire connectors. Note: Wire connectors provided
are suitable for copper wire only. For aluminum wire, consult an electrician.
Small:
Strip insulation 3/8 in (10 mm) for 14 AWG (1.5 mm²) wire
Strip insulation 1/2 in (13 mm) for 16 or 18 AWG (1.0 or 0.75 mm²) wire
Use to join one 14 AWG (1.5 mm²) supply wire with one 16 or
18 AWG (1.0 or 0.75 mm²) control wire.
Large:
Strip insulation 1/2 in (13 mm) for 10, 12 or 14 AWG
(4, 2.5 or 1.5 mm²) wire
Large
Small
Strip insulation 5/8 in (16 mm) for 16 or 18 AWG
(1.0 or 0.75 mm²) wire
Use to join one or two 12 or 14 AWG (2.5 or 1.5 mm²)
supply wires with one 10, 12, 14, 16, or 18 AWG
(4, 2.5, 1.5, 1.0 or 0.75 mm²) control wire.
5
Wiring the Dimmer.
• For installations involving more than one control in a wallbox, refer
to the section on Multigang Installations before beginning.
Wire location will vary by product.
NOTE:
Reference wires by color, not location.
5a - Single-Pole Wiring
Black
Green or Bare
Black Black
Green or Bare
120 V
60 Hz Light
Ground
5b - 3-Way Wiring
Tag
Black
Tag
Green or
Red
Bare
Black Red
Green or Bare Red
120 V
Dimmer 3-Way Switch
60 Hz
Ground
Backwired:
Insert
screwdriver.
Pull wire out.
6
Mount Dimmer to Wallbox.
• Form wires carefully into the wallbox,
mount and align dimmer.
• Install wallplate.
Start screws.
7
Turning ON Power.
• Turn power ON at circuit breaker
(or replace fuse).
• Connect the green or bare
dimmer ground wire to the bare
copper or green ground wire in the
wallbox. (See Important Note 4.)
• Connect one of the black dimmer
wires to either of the wires
removed from the switch.
• Connect the remaining black
dimmer wire to the other wire
Ground
removed from the switch.
Note: To use a 3-Way dimmer
in a single-pole application, cap
off one of the red wires and
follow instructions for single-pole
wiring. (If the on/off switch works
backwards, switch the red wires.)
• NOTE: Only one dimmer can be
used in a 3-WAY circuit.
• Connect the green or bare
dimmer ground wire to the bare
copper or green ground wire in the
wallbox. (See Important Note 4.)
• Connect the black dimmer wire
to the wire removed from the
different-colored screw on the
switch (marked or tagged wire).
Ground
Remove tag from wire.
• Connect one of the red dimmer
wires to either of the remaining
wires removed from the switch.
• Connect the remaining red
dimmer wire to the remaining wire
Light
removed from the switch.
Note: To install a
traditional style
wallplate, firmly pull
the Glyder or Rotary
®
knob to remove it.
Install the wallplate
and re-attach the knob.
Glyder
®
Align dimmer and
tighten screws.
Rotary