Table des Matières
Publicité
Storage conditions:
Products are stored in dry, ventilated warehouses at tem-
peratures from 0 ° C to +40 ° C with a relative humidity of
not more than 80% .
Transportation:
It is strongly perhebited dropping and any mechanical im-
pact on the pfckaging during transportation .
When unloading / loading, it is not allowed to use any
type of equipment that works on the principle of packing
clamping .
DESCRIPTION OF THE PRODUCT (Fig.2)
1.
Brush;
2.
Aluminum tube;
3.
Tube release button;
4.
Indicator light;
5.
Body release button;
6.
Power switch;
7.
Dust cup;
8.
Dust tank upper part
release button;
WARNING: To reduce the risk of fire, electrical
shock, or injury.
1.
Do not use outdoors or on wet surfaces;
2.
Do not allow to be used as a toy . Close attention is nec-
essary when used by or near children;
3.
Use only as described in this manual . Use only manu-
facturer's recommended attachments;
4.
Do not use vacuum if it has been dropped, damaged,
left outdoors, or dropped in water . Return it to an author-
ized service center;
5.
Do not handle plug or appliance with wet hands;
6.
Do not put any object into openings . Do not use with
any opening blocked; keep free of dust, lint, hair and any-
thing that may reduce air flow;
7.
Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts;
8.
Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or got ashes;
9.
Use extra care when cleaning on stairs;
10.
Do not use to pick up flammable or combustible liq-
uids such as gasoline or use in areas where they may be
present;
11.
Look on your vacuum and follow all label and marking
instructions;
12.
Keep end of hose, wands and other openings away
from your face and body;
13.
Do not use the vacuum cleaner without dust cup filter
in place;
14.
Always unplug this appliance before connecting or
disconnecting vacuum hose;
15.
Store the vacuum indoors . Put the vacuum away after
us to prevent tripping accidents;
9.
Dust tank bottom re-
lease button;
10.
Transformation joint;
11.
Multi crevice nozzle;
12.
Charger;
13.
Sponge, HEPA.
11
16.
Use the incorrect battery will damage motor and us-
ers . Please use the recommended batteries;
17.
Use only on dry, indoor surfaces;
18.
Do not use for any purpose other than described in
this user's guide;
19.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard .
PRECAUTIONARY MEASURES
If the opening that sucks in the air, the brush or exten-
sion tubes are blocked, you should switch off the vacuum
cleaner at once . First clear the blocked substance before
you attempt to start the vacuum cleaner again .
1.
Do not operate the vacuum cleaner too close to heaters
and like radiators, cigarette butts etc . (Fig . 3);
2.
Before you start using the vacuum cleaner,please
remove large or sharp objects from the floor in order to
prevent that the filter is damaged . Do not use the vacuum
to clean anything that is easy to burning, such as gas and
cigarettes (Fig . 4) .
ASSEMBLING VACUUM CLEANER
1.
Install the conversion connector (Fig . 5) .
When you need to be used directly to access the body
accessories, please use the conversion joint connection .
2.
Install extended aluminum tube (Fig . 6) .
We can use aluminum tube longer a head of connection
machine (after heard cut when installation, the installa-
tion is successful), and then the other side of the connect
accessories in the pipe (right), so that it can be used as
vertical vacuum cleaner:
* Connection after shangdi brush can be directly used to
clean the floor or carpet .
* Connected to brush or flat after absorption, can be used
to clean the ceiling, curtain is difficult to clean at ordinary
times, such as higher place, very convenient and practical .
3.
Remove and install the dust cup .
Remove dust cup from body: push the release button of
dust cup . Then take out the dust cup from body (Fig . 7) .
Install dust cup on body: first make the underside of dust
cup to connect with the body . (pls pay attention to the
fitting position and direction) . Then push the dust cup to
close with the body . The dust cup will be locked after a
voice of "kata" (Fig . 8) .
4.
Installation and remove the battery pack .
• Remove the battery pack: to promote the body BaoSuo
button at the bottom of the battery, and then along the
direction of mobile battery pack, so that you can remove
the battery pack from the body (Fig . 9) .
• Install the battery pack: according to the direction
along the guide into the battery pack, heard a loud
"crack" the sound of the dust cup lock (Fig . 10) .
5.
Indicator light (Fig .11) .
• In the work, the light of area A will be extinguished as
the quantity of electricity decreases, and the green light
of zone B will be always bright .
Publicité
Table des Matières
