S&P HV-150 A Manuel D'installation page 11

- It is recommended that you check the condition and operation of the appliance after unpacking it; any factory
defect is covered by the S&P guarantee.
Mounting on Glass windows (Glass thickness between 3 25 mm)
You can identify all the components of the device in figure A, and the measures required for the correct
installation of the device in figure B.
Cut a hole following the dimensions indicated on figure B. It is recommended that this should be a minimum
of 1,5 meters from ground level.
- Dismantle the HV-fan in accordance with the following instructions:
Fig. 1.- Loosen the retaining screw (b) fixing the internal front cover (a).
Fig. 2.- Remove the internal front cover (a) by pressing the knobs (c).
Fig. 3.- Unscrew the 3 bolts (d) fixing the external grille (e) and separate from the support plate (f).
- Install the HV on the glass as indicated below:
Fig. 4.- Pull the external grille (e) towards you and turn the rubber
the inner side of the grille.
Fig. 5.- From the outside, place the external grille (e) over the hole in the glass. From the inside, turn
push the rubber mountings (g) until they are located against the glass keeping the external grille (e) in its
correct position.
Fig. 6.- Mount the support plate (f) to the screws (h) of the external grille (e) and tighten the bolts (d) to suit
the thickness of the glass:
- Glass thickness 3 - 14 mm: Fig. 6a
- Panel thickness 14 - 25 mm: Fig. 6b
- Tighten the screws taking care not to flatten the rubber joints between the support plate and the external
grille.
Ensure that the glass is not in contact with the plastic frame.
Fig.7.- Make the necessary hole in the gland (i), and feed the electrical cables through the clamp (j) and
connect them in the terminal box (k).
Fig. 8.- Mount the internal cover (a) by slotting the rectangular openings (1) on the top of the cover (a)
into the receivers (m) of the support plate (f) until the two knobs (c) are correctly positioned.
Fig. 9.- Tighten the locking screw (b)
Wall mounting (wall thickness between 25 – 300mm)
(Ensure that threaded couplers and extended fixing rod (h) are supplied as accessories)
- Cut a hole in the wall where the unit is to be mounted, in accordance with the dimensions indicated in figure
B. It is recommended that this should be a minimum of 1,5 meters from ground level.
- Measure the thickness of the wall and cut the threaded rods (n) 5 mm shorter than this thickness.
- Use the appliance to mark on the wall the position of the fixing holes for the support plate (f), drill the fixing
holes and insert the wall plugs.
- Dismantle the HV-fan in accordance with the following instructions:
Fig.10.- Loosen the retaining screw (b) fixing the internal front cover (a).
Fig.11.- Remove the internal front cover (a) by pressing the knobs (c).
Fig.12.- Loosen the 3 bolts (d) fixing the internal grille (e) and separate it from the support plate (f).
- lnstall the HV-fan in the wall as follows:
Fig.13.- Pull the internal grille (e) towards you and take the rubber mountings (g) away from the screws (h).
Fig.14.- Fix the threaded rods (n) to the screws (h) on the external grille (e) with the threaded couplers (p)
supplied and put back the rubber mountings (g) on the rods.
Fig.15.- From the outside, place the external grille (e) over the hole in the wall. From the inside, turn and
push the rubber mountings (g) until
correct position.
Fig.16.- Mount the support plate (f) to the threaded rods (n) and tighten the bolts (d) to suit the length of the
rod sticking out from the support plate (f).
Fig.17.- Fix the support plate (f) to the wall and tighten bolts (d).
Fig.18.- Depending on the position of the incoming electrical cables, make a hole on the gland (i) on the
front cover (a) or in the gland (p) on
(j) and connect to the terminal box (k).
Fig.19.- Mount the internal cover (a) by slotting the rectangular openings (1) on the top of the cover (a) into
the receivers (m) of the support plate (f) until the two knobs (c) are correctly positioned.
Fig. 9.- Tighten the locking screw (b).
they are located against the wall keeping the external grille (e) in its
the support plate (f), introduce the electrical cables through the clamp
mounting (g) on the screws (h), towards
and
11