Publicité
Les langues disponibles
Les langues disponibles
H-4989
96
48" JUMBO
x
PACKING TABLE
TOOLS NEEDED
Phillips Head
Screwdriver
10 mm Wrench
WARNING! These instructions are for Jumbo Packing Tables only. Instructions for Deluxe Workstations are
included with H-5777 Uprights for Deluxe Workstation.
LEGS AND FRAME ASSEMBLY
1.
Insert adjustable feet (1) into legs (2) and slide into place
at desired height.
NOTE: If desired, insert locking tabs through legs
and adjustable feet to lock feet into place.
2. Place legs (2) in upright position. Legs should be placed
approximately 45" apart.
3. Attach stringers (3) to table legs using center six holes in
back legs. Fasten with 12 bolts, lock washers
and nuts, but do not fully tighten.
4. Place lower shelves (4) across braces of legs. Attach
lower shelves using 16 bolts and nuts. Now, fully fasten
hardware placed in step 3.
5. To attach tabletop (5) to frame assembly, place tabletop
on a smooth, non-marring surface with top side facing
down.
NOTE: If you have a Maple Jumbo Packing
Table, see Maple Tabletop Field Joint Assembly
instructions on page 2 before continuing to step 6.
6. Rotate the assembled frame upside down and line
up with the pre-drilled holes on the bottom side of the
tabletop.
PAGE 1 OF 6
1-800-295-5510
uline.com
7/16" Wrench
Flat Head
3/8" Wrench
Screwdriver
ASSEMBLY
#
1
2
3
4
5
1/4" x 20 x 5/8" Bolt x 28
Lock Washer x 12
4
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
DESCRIPTION
Adjustable Foot
Leg
Stringer
Lower Shelf
Tabletop
Hardware Kit
1/4" x 20 Nut x 28
#14 x 3/4" Wood Screw x 24
Locking Tab x 6
5
3
2
1
QTY
6
3
2
2
1
0721 IH-4989
Publicité
Table des Matières
Manuels Connexes pour Uline H-4989
Sommaire des Matières pour Uline H-4989
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-4989 1-800-295-5510 uline.com 48" JUMBO PACKING TABLE TOOLS NEEDED 7/16" Wrench Phillips Head Flat Head 3/8" Wrench Screwdriver Screwdriver 10 mm Wrench WARNING! These instructions are for Jumbo Packing Tables only. Instructions for Deluxe Workstations are included with H-5777 Uprights for Deluxe Workstation.
-
Page 2: Top Assembly
5. Before turning tabletop over, continue to Top Assembly instructions on page 1. Figure 3 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-4989... -
Page 3: Mesa De Trabajo
H-4989 800-295-5510 uline.mx MESA DE TRABAJO JUMBO 96 48" HERRAMIENTAS NECESARIAS Llave de 7/16" Desarmador con Desarmador Llave de 3/8" Cabeza Phillips Plano Llave de 10 mm ¡ADVERTENCIA! Estas instrucciones son para Mesas de Trabajo Jumbo solamente. Las instrucciones para las Estaciones de Trabajo de Alta Calidad vienen incluidas con el H-5777 Postes para Estación de Trabajo de... - Page 4 Diagrama 3 5. Antes de voltear la cubierta, continúe con las instrucciones de ensamble de la cubierta de la página 3. 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-4989...
-
Page 5: Outils Requis
H-4989 1-800-295-5510 uline.ca TABLE D'EMBALLAGE GRAND FORMAT DE 96 PO 48 PO OUTILS REQUIS Clé de 7/16 po Tournevis Tournevis Clé de 3/8 po cruciforme à tête plate Clé de 10 mm AVERTISSEMENT! Ces instructions se rapportent uniquement aux tables d'emballage de format géant. Les ARRÊT... -
Page 6: Montage Suite
éviter d'endommager le dessus de table, puis serrez complètement. Figure 3 5. Avant de retourner le dessus de table, continuez le montage en reprenant les instructions de montage du dessus à la page 5. 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-4989...