Pièces Et Caractéristiques - NuTone CT650 Instructions D'utilisation

PIÈCES ET CARACTÉRISTIQUES
Vous devez bien connaître les pièces et les caractéristiques de votre aspirateur
pour être en mesure de l'utiliser de façon appropriée et sécuritaire. Examinez l'il-
lustration ci-dessous avant d'utiliser l'aspirateur.
Article Pièce
Ampoule 9123A
Courroie 0518B
Cordon et porte-
cordon
Poignée de
la rallonge
Porte-cordon
Pédale de dégagement
rapide du manche
Numéro de
modèle/série
(sous l'appareil)
Pédale de dégage-
ment de la poignée
Pédale de réglage de la
hauteur des brosses
Capteur de saleté
Cordon d'alimentation
Courroie
Ampoule et lentille
Indicateur de hauteur
de la brosse
Brosses latérales
(non illustrées)
4
TROUBLESHOOTING
Review this chart to find do-it-yourself solutions for minor performance problems.
Any service needed, other than those described in this owner's manual, should be
performed by an authorized service representative.
! ! WARNING
Electrical Shock Hazard
Disconnect electrical supply before servicing or cleaning the unit.
Failure to do so could result in electrical shock or personal injury.
PROBLEM POSSIBLE CAUSE
Cleaner won't start. 1. Unplugged at wall outlet.
2. Tripped circuit breaker/blown fuse at household
service panel.
3. Loose hose electrical connections.
4. Tripped overload protector in Power Brush
Poor job of dirt pick-up. 1. Full or clogged dust bag.
2. Clogged airflow passages.
3. Dirty Filters
4. Wrong pile height setting
5. Open suction control
6. Hole in hose
7. Worn Power Brush agitator
8. Worn or broken belt
9. Dirty agitator or end caps
Cleaner starts but 1. Hose electrical connections.
cuts off.
2. Tripped overload protector in Power Brush.
3. Tripped overload protector in Power Unit.
1. Power Brush connections unplugged.
Power Brush will not
run when attached.
2. Worn or broken belt.
3. Dirty agitator or end caps.
4. Tripped overload protector in Power Brush
Constant green light on 1. Dirt passage is clogged.
in dirt sensor.
2. Lenses are dirty.
Any, some, or all red 1. Dirt passage is clogged.
light in dirt sensor burn
and never turn green.
No green or red dirt 1. No power to sensor board.
sensor lights.
Cleaner picks up move- 1. Wrong pile height setting.
able rugs or Power 2. Suction too strong.
Brush pushes too hard.
Light won't work. 1. Burned out light bulb.
Cleaner leaves marks 1. Wrong vacuuming pattern.
on carpet.
POSSIBLE SOLUTION
1. Plug in firmly, push ON/OFF switch to ON.
2. Reset circuit breaker or replace fuse.
3. Reconnect hose ends.
4. Clean agitator and end caps, then reset
(see page 9, 10, 11).
1. Change bag.
2. Clear airflow passages.
3. Change filters.
4. Adjust setting (page 7).
5. Adjust control (page 9).
6. Replace hose.
7. Change agitator (page 10).
8. and 9. See BELT CHANGING.
1. Check connections, reconnect hose ends.
2. Remove any items that may be caught or
jammed, then reset. If cleaner starts and stops
again, clean agitator and end caps, then reset
(page 9, 10, 11).
3. Change dust bag, clean airflow blockage.
Wait up to 50 minutes for motor to cool and
automatically reset.
1. Plug in firmly.
2. and 3. See BELT CHANGING AND AGITATOR.
CLEANING, (page 10).
4. Check agitator area for excessive lint build-up
or jamming. Clean agitator and end caps and
then reset.
1. Check for clogs in air passages (page 10).
2. Clean lenses (page 8).
1. Check for clogs in air passages (page 10).
1. Take to your nearest NuTone Service Center.
1. Adjust setting (page 7).
2. Open suction control (page 9).
1. Change light bulb (page 11).
1. See VACUUMING TIPS (page 7).
13