Product Specifications - F.F. Group EST 250 EASY Notice Originale

08 | English
*Double insulated: This product requires no
earth connection as supplementary insulation
is applied to the basic insulation to protect
against electric shock in the event of failure of
the basic insulation.
GUIDELINES FOR USING EXTENSION CORDS
Make sure your extension cord is in good condition.
f
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Always replace a damaged extension cord or have
f
it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
f
excessive heat and damp/wet areas.
Use a separate electrical circuit for your tools. This
f
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight con-
struction and intended for outdoor use.

PRODUCT SPECIFICATIONS

INTENDED USE
The product is intended for cutting weed, grass or
similar soft vegetation in areas that are hard to reach,
e.g. under bushes, on slopes and edges. It may not be
used to work on unusual thick, dry or wet grass, e.g.
pasture grass, or to shred leaves. For safety reasons
it is essential to read the entire instruction manual
before its first operation and to observe all the in-
structions therein. This product is intended for pri-
vate domestic use only, not for any commercial trade
use. It must not be used for any purposes other than
those described.
TECHNICAL DATA
Article Number
Model
Rated voltage
Rate power
No Load Speed
Cutting diameter
Cutting line thickness
Line length
Feed type
Weight
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
43 277
EST 250 EASY
V 230-240
Hz 50
W 250
rpm 13.000
cm 23
Ømm 1,2
m 4,5
Tap & Go
kg 1,3
Sound pressure level
Sound power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h ,HD
K
IDENTIFICATION
1. On/Off trigger
2. Upper handle
3. Front handle
4. Cable hook
5. Upper shaft
6. Shaft securing screw
7. Lower shaft
8. Motor body
9. Guard
10. Line cutting blade
11. Trimming line
ASSEMBLY
FITTING THE PROTECTIVE GUARD (C)
The protective guard is fixed to the motor body by
two screws in the positions shown below. The screws
are pre-fitted in these positions at the factory.
Remove the two screws from the motor body.
ƒ
Fit the guard onto the motor housing as shown.
ƒ
Fit the 2 x fixing screws to secure the guard.
ƒ
Carefully peel off the protective tape over the cut-
ƒ
ting blade fitted into the guard.
ASSEMBLING THE HANDLE (A)
The grass trimmer is supplied with the shaft in
two parts, connected together by the power ca-
ble. The two screws that join the shaft are pre-fit-
ted at the top of the lower shaft.
Remove the screws from the lower shaft.
ƒ
Taking care to feed the power cable into the upper
ƒ
shaft, fit the lower shaft into the upper shaft.
Screw the two screws into each side of the upper
ƒ
shaft to lock the two halves of the shaft together.
PREPARING THE GRASS TRIMMER
BEFORE EACH USE
WARNING! Danger of injury!
Check the product as well as accessories
ƒ
for damage before each use. Do not use the
product if it is damaged or shows wear.
Double check that accessories or applica-
ƒ
tion tools are properly fixed.
OPERATION
POWER CABLE (B)
NOTE: To avoid detaching the power ca-
ble always check that it is attached firm-
ly to the cable hook, before using the
EST 250 EASY
dB(A) 84
dB(A) 96
dB
(triax vector sum)
h
m/s 2,5
2
m/s 1,5
2
3