Precautionary Measures - Bort BSS-18DC-Multicyclone Mode D'emploi

14.
Always unplug this appliance before connecting or
disconnecting vacuum hose;
15.
Store the vacuum indoors . Put the vacuum away after
use to prevent tripping accidents;
16.
Use the incorrect battery will damage motor and us-
ers . Please use the recommended batteries;
17.
Use only on dry, indoor surfaces;
18.
Do not use for any purpose other than described in
this user's guide;
19.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard .

PRECAUTIONARY MEASURES

If the opening that sucks in the air, the brush or exten-
sion tubes are blocked, you should switch off the vacuum
cleaner at once . First clear the blocked substance before
you attempt to start the vacuum cleaner again .
1.
Do not operate the vacuum cleaner too close to heaters
and like radiators, cigarette butts etc . (Fig . 3);
2.
Before you start using the vacuum cleaner,please
remove large or sharp objects from the floor in order to
prevent that the filter is damaged . Do not use the vacuum
to clean anything that is easy to burning, such as gas and
cigarettes (Fig . 4) .
ASSEMBLING THE VACUUM CLEANER WITH AC-
CESSORIES
1.
Install the floor brush head (Fig . 5):
The floor brush head is suitable for all floors .
Floor brush head connected directly to the vacuum
cleaner body unit until you hear a audible clicking
noise .
Floor brush head connected with the aluminum tube
until you hear a audible clicking noise .
Disassemble the floor brush head (Fig . 5):
Press the tube release button, then remove the alumi-
num tube and floor brush head .
2.
Install the 2in1 crevice nozzle (Fig . 6):
The crevice nozzle is suitable for narrow gaps cleaning
and for using on upholstered surface cleaning .
Insert the 2 in 1 crevice nozzle into the connecting
joint, then insert the connecting joint to the vacuum
cleaner body unit .
The brush on the crevice nozzle can be pulled forwards
or backwards as need .
USE THE VACUUM CLEANER
1.
Install the battery pack (Fig . 7):
Slide the battery pack onto the body block until you
hear and feel it click into the place .
2.
Switch the vacuum cleaner on or off (Fig . 8):
To switch it on, press the power switch, button, the
vacuum cleaner is ON, and LED light is lighting up . If
you need the high suction for cleaning, press the high
mode button .
To switch it off, press the power switch button one
more .
CHARGE THE VACUUM CLEANER
The vacuum cleaner must be switched off for charging .
The rechargeable battery is not fully charged upon de-
livery . To reach the maximum charging capacity, charge
the appliance up fully before using it for the first time .
Charging the product (Fig . 9):
Plug the adapter plug into the connection socket on
the rear side of the vacuum cleaner .
The LED indicator light flashes one by one while it is
charging .
Once all the indicator light up, the battery is fully
charged .
Note: If the wrong adapter, during the charging, all the
LED light will flash quickly, not one by one flashed while
charging .
CLEAN THE VACUUM CLEANER
1.
Drop dust:
Push the dust cup bottom release button, then the dust
will fall down automatically . Usually you may only do
like this to drop the dust (Fig . 10)
Clean the dust cup . Press the dust cup release button,
then remove the dust cup from body .
Press the dust cup cover (for air exhaust) release but-
ton, take out the filter assembly out of the dust cup,
then you can clean them with soft brush or wash them
with water . You should dry them completely before you
use again (Fig . 11) .
Assemble the dust cup back after cleaning . Connect
the dust cup set to the body you hear a audible clicking
noise . The dust cup will be locked .(pleases pay atten-
tion to the fitting position and direction) .
2.
Clean the filter:
Take out the filter set (Fig . 12)
Clean the filter by soft brush or rinse it in water and
dry them completely before use again . All the filters are
washable . (we recommend you to clean the filters when
feeling the suction power becoming weak .)
Note: The above filters should be equipped in correct
places when work the vacuum machine .
3.
Clean the floor brush head (Fig . 13):
Remove the floor brush head from the vacuum cleaner
by pressing the release button . Slide the locking button
slightly . Take out the brush roller by hand .
If necessary, carefully remove dirt/hair with a pair of
scissors .
If need be, the brush roller can be washed . Let it dry
12