Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Operating Instructions
Series WC7000 Welding Cable Reels
Model Numbers:
WC7000
WCH7000
Dimensions
Four 1/2" diameter mounting holes
SAFETY
Personal injury and/or equipment damage may result if proper safety
precautions are not observed.
• Ensure that only a qualified electrician installs/services this
equipment.
• Ensure that power supply voltage does not exceed maximum
voltage rating of reel.
• Ensure that reel is properly installed before connecting to power
supply.
• Ensure that all electrical power is removed from reel before ser-
vicing.
• Check for frayed/broken wires before each use.
• Pull electrical cord from reel by grasping the electrical cord
itself, not the work device.
• If an electrical malfunction should occur, remove power from reel
immediately.
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
WC7000 WCH7000
A
20 1/4"
20 1/4"
B
19 3/4"
19 3/4"
C
7 7/8"
7 7/8"
D
3 7/8"
3 7/8"
E
13 1/4"
14"
IMPORTANT
Read this manual carefully before installing, operating or
servicing this equipment.
• Ensure that reel, electrical cable, and equipment being serviced
are properly grounded. Use an ohmmeter to check ground
continuity.
• If reel ceases to unwind or rewind, remove power immediately.
Do not pull or jerk on electrical cable!
• Treat and respect the cable reel as any other piece of machinery,
observing all common safety practices.
WARNING: Even low voltage can cause irreparable damage or
death! Exercise extreme caution while operating or servicing this
equipment.
WARNING: This reel is to be used for cable storage only! The
entire length of cable must be unwound before use. Severe dam-
age to the reel will result if the cable is energized while fully
wound on the reel.
Form# 1154-304 Rev: 10/2018

Publicité

loading

Sommaire des Matières pour Reelcraft WC7000 Serie

  • Page 1 • If an electrical malfunction should occur, remove power from reel immediately. Form# 1154-304 Rev: 10/2018 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 2 8. Wind cable onto spool by squeezing through gap between spool and guide arm (8). 9. Once cable is wound on the spool add additional turns (2-3 should be sufficient) to add tension to cable. 10. Add bumper (9) to cable at desired location. Page 2 www.reelcraft.com...
  • Page 3 11 Base Assembly S600016 S600016 29 U-Bolt 3-117440 3-117440 12 1/2-13 Set Screw S35-84 S35-84 30 1/4-20 x 3/8” Locknut 261650-1 261650-1 13 Guide Arm Assembly S600017 S600017 --- Inlet Cord Assembly 261603 262930 14 5/16-18 Locknut 300107 300107 www.reelcraft.com Page 3...
  • Page 4 • al carrete. • • Form# 1154-304 Rev: 10/2018 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 5 8. Rebobine el cable sobre la bobina insertándolo a través del espacio entre la bobina y el brazo guía (8). 9. Una vez que el cable haya sido embobinado sobre la bobina, gire la manivela 2 ó 3 vueltas adicionales para tensionar el cable. 10. Agregue un tope (9) al cable en la ubicación deseada. www.reelcraft.com Page 5...
  • Page 6 29 Perno en U 3-117440 3-117440 12 Tornillo de retención, 1/2-13 S35-84 S35-84 30 Contratuerca, 1/4-20 x 3/8” 261650-1 261650-1 13 Conjunto de brazo guía S600017 S600017 --- Ensamble del cable de entrada 261603 262930 14 Contratuerca, 5/16-18 300107 300107 Page 6 www.reelcraft.com...
  • Page 7 Utilisez un ohmmetre pour vérifier la continuité la terre. Form# 1154-304 Rev: 10/2018 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 8 8. Enroulez le cèble sur le tambour en le pressant dans l’espace entre tambour et bras de guidage (8). 9. Une fois le cèble enroulé sur le tambour ajoutez quelques tours de plus (2-3 devraient suffire) pour ajouter de la tension au cèble. 10. Ajoutez le butoir (9) au cèble l’emplacement voulu. Page 8 www.reelcraft.com...
  • Page 9 29 Étrier fileté 3-117440 3-117440 12 Vis de calage 1/2-13 S35-84 S35-84 30 Contre-écrou 1/4-20 x 3/8” 261650-1 261650-1 13 Ensemble de bras de guidage S600017 S600017 --- Ensemble de cordon d’entrée 261603 262930 14 Contre-écrou 5/16-18 300107 300107 www.reelcraft.com Page 9...

Ce manuel est également adapté pour:

Wch7000 serie