White-Rodgers 24A07 Instructions D'installation

WHITE-RODGERS
Operator: Save these instructions for future use!
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
These Level-Temp Silent Operator relays are designed
for use on electric heating equipment in conjunction with
White-Rodgers low voltage thermostats. They are espe-
cially suitable for use on baseboards, wall insert heaters,
etc. Some models also have an inductive rating to permit
them to be used on motor loads where a time delay is
desired.
Different models of these Silent Operator relays are
available for voltage inputs of 120, 208, 240, 277, 347 or
600 volts. Since these relays are equipped with a self-
contained transformer, the supply voltage used must
agree with the voltage rating of the relay.
If in doubt about whether your wiring is millivolt, line, or
low voltage, have it inspected by a qualified heating and
air conditioning contractor, electrician, or someone famil-
iar with basic electricity and wiring.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical
codes and ordinances.
This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction.
ELECTRICAL DATA
Switch Action: Single-Pole, Single-Throw, normally open
Thermal: Average time delay – 45 seconds
Ambient Temp.: -20° to 140°F (-24° to 60°C)
TYPE
NUMBER VOLTAGE /FREQUENCY
24A07A-1 120VAC, 60 Hz
24A07E-1 208VAC, 60 Hz
24A07G-1 240VAC, 60 Hz
24A07Z-1 277VAC, 60 Hz
24A07Z-8 347VAC, 60 Hz
24A07Z-9 600VAC, 60 Hz
Mounting: Mounting tabs with several break-offs for 2, 3 or 4 hole mounting.
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
(314) 577-1300,
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653, FAX (905) 475-4625
INPUT THERMOSTAT
CURRENT
0.2A
0.2A
0.2A
0.2A
0.2A
0.2A
FAX (314) 577-1517
TYPE 24A07
"SLIMLINE" LEVEL-TEMP
SILENT OPERATOR
INSTALLATION INSTRUCTIONS
When required, two or more of these Silent Operator
relays can be operated by one low voltage heating
thermostat. These Silent Operator relays have been
carefully adjusted at the factory. No attempt should be
made to adjust them in the field.
To prevent electrical shock and/or equipment
damage, disconnect electric power to system, at
main fuse or circuit breaker box, until installation
is complete.
Do not use on circuits exceeding specified
voltages. Higher voltages will damage control
and could cause shock or fire hazard.
Room Thermostat:
Set adjustable heat anticipator at 0.2 Amps. For fixed
anticipation thermostats, use 0.15 to 0.25 Amp. heater.
A.C.
RESISTIVE
NON-INDUCTIVE
25A, 3000W, 120V
25A, 5200W, 208V
25A, 6000W, 240V
22A, 6000W, 277V
17A, 5900W, 347V
12A, 7200W, 600V
Printed in U.S.A.
(Normally Open)
DESCRIPTION
PRECAUTIONS
CAUTION
WARNING
SPECIFICATIONS
A.C. MOTOR INDUCTIVE
FULL LOAD LOCKED ROTOR
16A, 120V 96A, 120V
12A, 208V 72A, 208V
12A, 240V 72A, 240V
PART NO. 37-4709C
Replaces 37-4709B
0023