Work Method; Preparation And Warnings; Battery Charge Level Controls; Indirect Scrubbing Or For Very Dirty Surfaces - GGMgastro BSW1400 Mode D'emploi

Model "BSW1400"
- Verify that the battery connector placed in the
back of the machine ( Photo D - 7) is connected.
- Put the ignition key ( Photo D - 1) in and turn ON
the machine.
- In the control panel, check the battery charge sta-
tus ( Photo C - 3 )
- Switch ON the brush motor switch ( Photo C - 1).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo D - 2).
- Switch ON the suction motor switch ( Photo C - 2).
- Open the water outlet lowering the control lever
( Photo D - 8)
- Lower the squeegee unit by using the lift/lower
lever ( Photo D - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo D - 3)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo D - 2); releasing the
lever the brush rotation will stop after few seconds.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model "BT"
- Verify that the battery connector placed in the
back of the machine ( Photo F - 8) is connected.
- Put the ignition key ( Photo F - 1) in and turn ON
the machine.
- In the control panel, check the battery charge sta-
tus ( Photo E - 1 ) and, if sufficient, select the run-
ning speed wished ( Photo E - 3, E - 4 ).
- Switch ON the brush motor switch ( Photo E - 5).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo F - 2).
- Switch ON the suction motor switch ( Photo E - 6).
- Open the water outlet lowering the control lever
( Photo F - 9)
- Lower the squeegee unit by using the lift/lower
lever ( Photo F - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo F - 3)
- Wash the floor moving forward by pulling the trac-
tion lever ( Photo F - 2) up or push the traction
lever down to reverse traction; releasing the lever
the traction will stop immediately and brush rota-
tion will stop after few seconds.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.

6.14 WORK METHOD

6.14.1 PREPARATION AND WARNINGS

Remove any loose solid residue from the surface to
be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from operat-
ing correctly, reducing drying efficiency.
Only trained personnel can drive this machine.

6.14.2 BATTERY CHARGE LEVEL CONTROLS

The sequence of lights of the battery charge control
( Photo C - 3, E - 1 ) progressively turns off until the
battery is discharged . When the red light turns on
( Photo C - 3C, E - 1C ), turn off the brush motor,
close the detergent solution outlet, finish drying the
small residual moisture and go to the battery charg-
ing area to charge the battery.
!
( ) The batteries may be irreparably dam-
aged if the residual charge level drops too
low (see the battery operating manual). Do
not force the battery discharge beyond the
safety limits, turning the key off and on or in
any other manner.
6.14.3 DIRECT
SLIGHTLY DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and
use it as described in paragraph 6.13.
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.
6.14.4 INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 6.13,
without drying the floor
Allow the detergent solution to work on the
dirty floor according to what is indicated in
the information relative to the detergent
used.
Second set of operations:
Proceed as explained in the previous "Direct Wash-
ing" paragraph (6.14.3) to also proceed with drying
the floor.
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.

6.14.5 POST-SCRUBBING OPERATIONS

Close the detergent solution outlet.
Lift the brush unit and turn off the brush motor.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks;
empty and clean the tanks (as described in 6.11).
Turn off the machine using the key and remove it
from the control panel.
If necessary, charge the battery (see the relative
section).

7. MAINTENANCE INFORMATION

( ) Turn the key, remove it from the control panel
and disconnect the battery from the machine
wiring.
39
SCRUBBING OR FOR