Important Safety Instructions - Lithonia Lighting OMS 1000 Instructions D'installation

reaD anD follow tHese safety instructions!
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards please
read all warnings and instructions included with and on the fixture box
and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this
equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should
be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician
and check your local electical code.
• Maintenance of the luminaires should be performed by person(s)
familiar with the luminaires' construction and operation and any hazards
involved. Regular fixture maintenance programs are recommended.
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
• It will occasionally be necessary to clean the outside of the refractor/
lens. Refractor/lens should be washed in a solution of warm water and
any mild, non-abrasive household detergent, rinsed with clean water and
wiped dry. Should optical assembly become dirty on the inside, wipe
refractor/lens and clean in above manner, replacing damaged gaskets
as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been
properly packed so that no parts should have been damaged during
transit. Inspect to confirm. Any part damaged or broken during or after
assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products,
please visit www.epa.gov.
• These instructions do not purport to cover all details or variations
in equipment nor to provide every possible contingency to meet in
connection with installation, operation, or maintenance. Should further
information be desired or should particular problems arise which are not
covered sufficiently for the purchaser's or owner's purposes, this matter
should be referred to Acuity Brands Lighting, Inc.
warning
risk of electric sHock
► Disconnect or turn off power before installation or servicing.
► Verify that supply voltage is correct by comparing it with the luminaire
label information.
► Make all electrical and grounded connections in accordance with
the National Electrical Code (NEC) and any applicable local code
requirements.
► All wiring connections should be capped with UL approved wire
connectors.
caution
risk of injury
► Wear gloves and safety glasses at all times when removing luminaire
from carton, installing, servicing or performing maintenance.
► Avoid direct eye exposure to the light source while it is on.
warning
risk of Burn
► Allow lamp/fixture to cool before handling. Do not touch enclosure, lens
or light source.
► Do not exceed maximum wattage marked on luminaire label.
► Follow all manufacturer's warnings, recommendations and restrictions
including but not limited to: driver type, burning position, mounting
locations/methods, replacement and recycling.
► Use only lamps that comply with ANSI standards.
All manuals and user guides at all-guides.com
► Keep combustible and other materials that can burn, away from lamp/
► Do not operate in close proximity to persons, combustible materials or
► Never connect components under load.
► Do not mount or support these fixtures in a manner that can cut the outer
► Unless individual product specifications deem otherwise: Never connect
► Unless individual product specifications deem otherwise: Do not restrict
► Unless individual product specifications deem otherwise: Do not exceed
► Only use fixture in its intended location.
► LED products are Polarity Sensitive. Ensure proper Polarity before
► Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal
► Do not touch individual electrical components as this can cause ESD,
► Some components inside the fixture may not be serviceable. In the
► Changes or modifications not expressly approved by Acuity Brands
► Always read the fixtures complete installation instructions prior to
Register your warranty on www.lightahome.com/warranty. Your prompt
product registration confirms your right to the protection available under
the terms and conditions of your Lithonia Lighting warranty.
Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit www.
acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities
for claims arising out of improper or careless installation or handling of its
products.
page 2

iMPortant safety instructions

caution
risk of fire
lens.
substances affected by heat.
caution
risk of ProDuct DaMage
jacket or damage wire insulation.
an LED product directly to a dimmer packs, occupancy sensor, timing
device, or other related control devices. LED fixtures must be powered
directly off a switched circuit.
fixture ventilation. Allow for some volume of airspace around the fixture.
Avoid covering LED fixtures with insulation, foam, or other material that
will prevent convection or cooling.
fixtures maximum ambient temperature.
installation.
grounding equipment must be worn during all installation or servicing
of unit.
shorten lamp life, or alter performance.
unlikely event your unit may require service, stop using the unit
immediately and contact an ABL representative for assistance.
Lighting could void the authority to operate the equipment.
installation for any additional fixture specific warnings.
5-year liMiteD warranty