How To Use - Remington HIGH PRECISION BHT-2000 Guide D'utilisation Et D'entretien

CS27555_BHT2000_IB 8/31/05 5:14 PM Page 6

How to Use

Charging the BHT-2000
Before using the for the first time, it must
charge for 14-16 hours.
1. Make sure the groomer is turned off.
2. Connect the cord to the unit, then plug
the charging adapter into the electrical
outlet. A charging indicator will light up.
3. Your groomer cannot be over charged so
you can leave it plugged in and charged
between uses, but if the unit is not going
to be used for an extended period of
time (2-3 months) unplug it and fully
recharged when you want to use it
again.
4. Only use the charging adapter supplied
with the unit.
5. Charging should be done at temperature
between 4ºC and 35ºC, or it could
decrease the battery's life.
6. To preserve the life of the batteries, let
them run out every 6 months, than
recharge them for 24 hours.
7. This product is intended for cordless use
only.
Before using your groomer: The High
Precision Body Hair Trimmer Shaver is
washable so it can be used in the shower
or rinsed under water during cleaning.
Therefore, to maintain the performance of
the cutters, oil before each use and after
rinsing. Turn the trimmer on to distribute
the oil evenly. Prior to using, wipe off any
excess oil. Be sure that the groomer is
truned off when applying the oil.
Take a moment
Be patient when first using your BHT-2000.
As with any new product, it may take a
little while to familiarize yourself with it,
especially if you are using a trimmer for all
the first time or are using a different brand.
6
Take the time to acquaint yourself with your
new trimmer, as we are confident you will
receive years of enjoyable use and
complete satisfaction.
Trimming
Use the thumb wheel to set the trimmer
comb to the desired length setting. It's
a good idea to begin trimming at one
of the longest settings (4 or 5) to avoid
accidentally trimming hair too short. As
you become familiar with the settings,
you can then select your desired length
setting.
Turn the unit on.
Place the flat top of the trimmer comb
against the skin.
If hair builds up in the trimmer comb
during the trimming process, switch the
unit off, pull off the adjustable trimmer
comb and brush/rinse it off.
For an even closer look and precise
shaping, remove the adjustable trimmer
comb and trim the hairs along the outer
edge.
When you are finished, turn the trimmer
off, clean it, and return it to its storage
pouch.
Adjusting the trim length
The trimmer comb can be adjusted to give
you 5 different trim lengths simply by by
turning the thrmb wheel to the desired
setting. Turn the thumb wheel clockwise
for a shorter length, counter-clockwise for
longer length. The wheel will click into
place as it reaches each setting, and the
setting number will appear on the length
position indicator. Here's what the length
settings mean:
Setting Length
1 3mm
2 5mm
3 7mm
4 8mm
5 12mm
! Trimmer comb must be attached to the
trimmer in order to use the hair length
selector.
Edging and shaping
Remove the trimmer comb attachment.
Hold the trimmer at a right angle to
your skin and press down gently.
Edge and shape the area as desired.
Using the shaver attachment
Hold the shaving head to your skin.
Stretch your skin with your free hand so
hairs stand upright.
Only apply light pressure on the shaving
head while shaving.
Shave against hair growth.
! The Microscreen shaving technology with
circular foil holes is developed to give a
controlled close cut.
Removing the trimmer comb and cutting
assembly
Be sure trimmer is off.
The trimmer comb
may be on any setting.
Hold the trimmer in
one hand with your
thumb firmly on the
thumb wheel to keep
it from turning.
With your other hand,
gently pull the trimmer
comb attachment off
the trimmer.
Remove the cutting assembly by firmly
pushing up on the blade with your
thumb. The cutting assembly rests on
a gentle spring. Use your other hand to
cover the cutting assembly to prevent
accidents.
Removing the shaver attachment
Ensure the trimmer is off.
Hold the trimmer in one hand with your
thumb firmly on the thumb wheel to
keep it from turning.
With your other hand, gently pull the
shaver attachment off the trimmer.
Removing the shaver cover
Ensure the trimmer is off.
Gently push the buttons either side of
the shaving foil. With the other hand lift
the shaver cover. Clean then replace.
Replacing the cutter assembly
Ensure the trimmer is off.
Hold the trimmer in one hand. With your
other hand, insert the
lower part of the cut-
ter assembly into the
trimmer, push down
the cutter until firmly
attached.
Replacing the trimmer comb and shaver
attachment
Hold the trimmer in one hand with your
thumb firmly on the thumb wheel to
keep it from turning. Ensure that the
length position indicator is at 1.
Slide the comb/shaver down the
grooves until it clicks into place.
! The trimmer comb and shaver attachment
can only be attached in one way. If it does
not go on correctly, turn it around and try
again.
7