t.a.c. C-60 Manuel D'utilisation page 20

C-60 24.04.2009 16:53 Uhr Seite 38
OPERATING THE APPLIANCE
ADVANCED PLAYBACK FUNCTIONS
Operation Button(s) Description
With this function it is possible to set up a desired playing sequence of the
CD tracks. This also allows you to play a smaller selection of your own choi-
ce from all the CD tracks. This programming can only be done with the remo-
te control. The "program" is set up by the following procedure:
PGM (29)
Program the playback
order
Number keys
(19)
The "REPEAT" play function (7)(31) can also be applied to the programmed
track selection. You can see on the display (4) from the text "PGM" that a
program is active. It is only if you press "PGM" again, eject the CD or switch
off the CD player that your own playing sequence is deleted.
The function activated with this remote control button brings about all the CD
tracks to be played in random order. If this button is pressed during play or
Switch between normal pause, the current track is stopped and the playing of all the CD tracks in
RANDOM
and random playback random order begins. In the display, this play mode will be indicated by the
(30)
text "RAN". Pressing the "RANDOM" button again switches off random
playing and playing will continue from the current position.
If this button is pressed once while the CD is playing, the current track will
Switch between playing be played over and over again. In the display (4) this operation mode is
the content of the CD indicated by the text "REPEAT 1". If this button is pressed twice while the
REPEAT
once, repeating an indivi- CD was playing, then the entire CD or the entire program will be played
(7)(31)
dual track and repeating over and over again. In the display this operation mode is indicated by
all the tracks on the CD the text "REPEAT ALL". A third keystroke switches off this function. The desi-
red repeat mode can also be switched on for a selected program (29).
38
tube·amp·company
• Press the button "PGM".
• Enter the numbers of all the desired tracks one after the other on
the number pad of the remote control. For track 10 use the "10"
button. For all other two-digit track numbers first press the "10+"
button as many times as necessary until the number of 10's is cor-
rect. If the second digit is a zero no additional keystroke is neces-
sary. If the second digit is from the range 1..9 press the correspon-
ding number key (example: for track 23 press the "10+" button
twice and the "3" button once).
• To confirm the program press "STOP" (9)(25) or "PGM".
OPERATING THE APPLIANCE
ADVANCED PLAYBACK FUNCTIONS
Operation Button(s) Description
While the CD is playing, the first touch to this key marks the start of the
section (A) and the second touch marks the end of this section (B). As
soon as both points are selected, the player continues to play the defined
Repeat a custom section
section over and over again until the "A-B" key is pressed again or
of the track as an end-
A-B (20)
"STOP" (9)(25) is pressed. In the display (4) this play mode is indicated
less loop
with the symbol "A
the "STOP" key (9)(25), the marked points will be deleted. This play opti-
on too can only be controlled via the remote control.
You can press this remote control key if the beginning of every track is only
to be played for a brief time. In this mode the first ten seconds of the track
will be played then it will skip to the next track in the sequence. This function
is also known by the term "Intro Scan". Even if a program has been set up
Play a short introduction
INTRO (21) for the play sequence (29), all the CD tracks will each be played once for
of every track
a brief time after the "INTRO" key has been pressed. Pressing this key
again ends the Intro Mode and continues playing the remaining section
from the current position onwards. The text "INTRO" will be shown on the
display (4) while the "Intro Scan" is active.
After pressing this remote control key while the CD is playing, the remai-
ning time of the current track will be shown (indicated by the text
Indication of the remai- "REMAIN" in the display (4)). Pressing the key again switches the display
REMAIN (18)
ning playing time to the remaining playing time of the entire CD or the entire program, with
the display then showing "REMAIN ALL". Pressing the key a third time
switches back to the normal playing time display.
£ B". After the A-B playback has been stopped with
tube·amp·company
39