Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
RPLS730B / RPLS731B
Programmable Wall Switch
APPLICATIONS
The RPLS730B / RPLS731B programmable wall switch has been designed to
control lightings and motors:
Load type
Resistive load 2400 W (20 A @ 120 V) •
Inductive load 2400 W (20 A @ 120 V) •
Motor
1 hp
INSTALLATION
NOTE:
This switch cannot be used if there are not at least 2 white wires joined
by a connector inside the electrical box.
1.
Cut power at the circuit breaker to avoid electric shock.
2.
Remove the existing switch.
3.
Install the new switch as shown in the diagram below.
4.
Apply power at the circuit breaker.
120 VAC (line)
black (line)
INSTALLATION AND USER GUIDE
Maximum load
blue (load)
incandescent lights
•
halogen lights
•
block heater
fluorescent lights
•
compact fluorescent lights (CFL)
•
sodium lamps
•
electronic ballasts
•
pool filter pumps
•
fans
white (neutral)
Examples
Load
M38497
69-2457EFS-03
Publicité
Table des Matières
Manuels Connexes pour Honeywell Home RPLS730B
Sommaire des Matières pour Honeywell Home RPLS730B
- Page 1 RPLS730B / RPLS731B Programmable Wall Switch INSTALLATION AND USER GUIDE APPLICATIONS The RPLS730B / RPLS731B programmable wall switch has been designed to control lightings and motors: Load type Maximum load Examples Resistive load 2400 W (20 A @ 120 V) •...
-
Page 2: Setting The Clock
RPLS730B / RPLS731B PROGRAMMABLE WALL SWITCH POWER-ON Pry the switch door open from the bottom using a small screwdriver. Ensure the ON/OFF selector is set to ON. Reset Reset the switch using a paper clip. 0:00 will flash. Control (4) If the display is blank: •... - Page 3 RPLS730B / RPLS731B PROGRAMMABLE WALL SWITCH PROGRAMMING THE SCHEDULE You can set up to 7 programs. To set a program, you need to enter its start time (ON) and its end time (OFF). Pry the switch door open using a small screwdriver.
-
Page 4: Technical Specifications
69-2457EFS—03 M.S. Rev. 09-20 | Printed in United States www.resideo.com © 2020 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates. -
Page 5: Interrupteur Mural Programmable
RPLS730B / RPLS731B Interrupteur mural programmable MODE D’INSTALLATION ET D’EMPLOI APPLICATIONS L’interrupteur mural programmable RPLS730B / RPLS731B a été conçu pour commander des appareils d’éclairage et des moteurs. Type de charge Charge maximale Exemples 2400 W (20 A @ 120 V) •... -
Page 6: Démarrage
RPLS730B / RPLS731B INTERRUPTEUR MURAL PROGRAMMABLE DÉMARRAGE Soulevez le bas du couvercle de l’interrupteur à l’aide d’un petit tournevis. S’assurer que le sélecteur ON/OFF est placé à ON. réinitialisation Réinitialiser l’interrupteur à l’aide d’un trombone. 0:00 clignotera à l’écran. touche de contrôle (4) -
Page 7: Programmation De L'horaire
RPLS730B / RPLS731B INTERRUPTEUR MURAL PROGRAMMABLE PROGRAMMATION DE L’HORAIRE Vous pouvez enregistrer jusqu'à 7 programmes. Pour enregistrer un programme, vous devez régler l’heure du début (ON) et l’heure de la fin (OFF). Soulevez le bas du couvercle de l’interrupteur à l’aide d’un petit tournevis. -
Page 8: Fiche Technique
69-2457EFS—03 M.S. Rev. 09-20 | Imprimé aux États-Unis www.resideo.com © 2020 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates. - Page 9 RPLS730B / RPLS731B Interruptor mural programable GUÍA DE INSTALACIÓN Y USO DESCRIPCIÓN El interruptor mural programable RPLS730B / RPLS731B se utiliza para controlar dispositivos de alumbrado y motores. Tipo de carga Carga máxima Ejemplos Carga 2400 W (20 A @ 120 V) •...
-
Page 10: Modos De Funcionamiento
RPLS730B / RPLS731B INTERRUPTOR MURAL PROGRAMABLE ENCENDIDO Levantar la tapa del interruptor con un pequeño destornillador. Asegurarse de que el selector ON/OFF esté en reinicialización Presionar en Reinicialización con un botón de control (4) sujetapapeles. 0:00 parpadeará en la pantalla. -
Page 11: Programación
RPLS730B / RPLS731B INTERRUPTOR MURAL PROGRAMABLE PROGRAMACIÓN Se pueden registrar hasta 7 programas. Para registrar un programa, debe definirse la hora de inicio (ON) y la hora de finalización (OFF). Levantar la parte inferior de la tapa del interruptor con un pequeño destornillador. -
Page 12: Asistencia Técnica
69-2457EFS—03 M.S. Rev. 09-20 | Impreso en Estados Unidos www.resideo.com © 2020 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.