Turbosound TCS-AN Serie Mode D'emploi page 8

14
TCS-AN SERIES
TCS-AN DSP Menu Structure
Fullrange
None
PROCESS EQ
Array2
Array3
User
Low/ High Shelving
Sub menu
Parametric 1 & 2
None
XOVER
HP 100 Hz
HP 120 Hz
User
Freq
Sub Menu
Phase
Auto
FBQ
Single
Learn
Reset
Input
SETUP
INPUT
(page 1)
Volume
Sensitivity
Subwoofer Function
None Sets the frequency response to the default setting.
Sets a corrected frequency response for 2 cabinets
–
arrayed together.
Sets a corrected frequency response for 3 or more
–
cabinets arrayed together.
Lets you define your own frequency response setting
User
by entering the corresponding sub-menu.
Low/ High Shelving Lets you define a low and high shelving filter.
Lets you define a parametric bell-type EQ (Frequency,
Parametric 1 & 2
Qual. and Gain).
– Unit is set for default full-range reproduction.
Preset with 100 Hz, 24 dB/octave filter for crossover
LP 100 Hz
between subwoofer and full-range speakers.
Preset with 120 Hz, 24 dB/octave filter for crossover
LP 120 Hz
between subwoofer and full-range speakers.
User crossover sub menu for combination with other
User
full-range or subwoofer speaker systems
Select the desired crossover frequency:
Freq • Fullrange Systems: 75 Hz to 400 Hz.
• Subwoofer Systems: 50 Hz to 150 Hz.
Phase Adjust the absolute phase (0° or 180°).
Automatically sets as many filters as required.
Whenever a new feedback frequency is discovered,
Auto
the first filter will be released to attenuate the new
frequency, and so forth.
Activates the FBQ (feedback detection) functionality,
Single
up to 8 feedback filters.
Automatic procedure which searches for feedback
frequencies and locks settings after all 8 filters have
been set.
Learn WARNING!
Please use ear protection during this procedure. The
feedback signal may approach the system's maximum
level, which may cause hearing damage!
Reset Resets all filters.
Lets you choose the audio input source. Choose
between Local (analogue Input) or ULTRANET
Input
(e.g., P16 monitoring system or M32 audio via
ULTRANET).
Adjusts the input gain. With ULTRANET digital inputs
Volume over a range from + 10 dB to - 30 dB. With analogue
input from 0 dB to - ∞ dB.
Adjusts input sensitivity for maxium output when
Sensitivity using an analogue source +4 dBu for normal
opperation, + 14 dBu for high level input.
Fullrange
Free
POSITION
Wall
Ceiling
Corner
Screenshot update Delay
DELAY
Unit
Limit
LIMITER
Version
SETUP
(page 2)
1. - 20.
LOAD
1. - 20.
SAVE
Save Preset
Sub Menu
Contrast
SETUP
Screen
Lock
Sub Menu
Warning
15
Quick Start Guide
Subwoofer Function
For positioning the speaker in free suspension or
–
ground stacked away from walls.
For positioning the speaker on or next to a wall, or on
Floor
the floor (subwoofer)
For positioning the speaker near the ceiling and wall,
Wall
or floor and wall (subwoofer)
For positioning the speaker in a corner next to the
Corner ceiling (fixed install) or in a corner on the floor
(subwoofer)
Adjusts the amount of delay (max 300 msec = 103 m
Delay
or 338 feet).
Unit Selects between msec, meters and feet.
Adjust the limiter threshold for the input signal (from
OFF up to -30 dB). This threshold adjustment allows
Limit
you to set a max output power which is below the
loudspeaker system's rated max output.
Version Displays the installed firmware version.
To load a specific preset, turn the encoder to select
the desired preset's number, and then press either
1. - 20.
the ENTER button or the encoder. When asked to
confirm press the encoder again or EXIT to abort.
To save a preset choose the respective preset slot and
1. - 20.
press ENTER or the encoder.
Name the preset by choosing the characters with
the encoder and pressing to confirm each character.
Save Preset
When finished, press the ENTER button to save the
preset.
Adjust LCD panel contrast. The default contrast value
Contrast
is 15.
ON: LCD screen saver (default) turns on automatically
after approx. 2 minutes.
Screen
OFF : LCD turns off automatically after approx. 5
minutes.
Lock the device and create a password by choosing
the password characters with the encoder and
pressing to confirm each character. When finished
Lock press the ENTER button. Unlock the device by
entering the password or connecting the unit via USB
to a PC running proprietary remote software. The
software does not require a password.
In case of overheating, an alert appears on the LCD
Warning screen, and the amplifier will shut down until the
unit cools