Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Vehicle
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75529F
Wrenches: 18mm
Drill Bits: None
18mm crowfoot adaptor,
3/8" or 1/2" universal adaptor,
3/8" or 1/2" x 6" extension
2
1
Qty. (6)
12mm-1.75 X 35mm Cl 10.9 Hex head bolts
1
1.
Open vehicle back hatch door and open compartment in floor to access spare tire lowering screw. Use 19mm socket to turn
screw counter-clockwise and lower spare tire to allow easier access for installing bumper bolts.
2
2.
It may be necessary to temporarily lower exhaust system to allow for easier access to install frame bolts. If necessary remove
It
b
(2) rearward rubber isolator hangers per side. Spraying with a lubricant will aid in removing isolators off of studs.
3.
Raise hitch into position as shown above. Locate bumper bracket above vehicle fascia first before raising. It may be necessary
to pull down on bumper fascia slightly to get bracket in place.
4.
Install 12mm bolts and conical washers supplied as shown above.
5.
Use crowfoot adaptor and extension to torque 12mm bolts in bumper. Access from in front of hitch between spare tire.
6.
Reinstall exhaust hangers if removed. Raise spare tire back into position. Torque all fasteners to specifications below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2011 Cequent Performance Products
Installation
Fascia
Bumper
t t
il l
h
Tighten all 12mm fasteners with torque wrench to 92 lb.-ft., 125 N*M
Ti h
ll 12
f
Instructions
Suzuki XL7
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1 & SUV2
2
1
Qty. (6)
2
t
t
t
ll
f
i
i h
h
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT
4000lb. (1816 Kg)
4000 lb. (1816 Kg)
1/2" Conical washers
t i
t ll f
b lt
92 lb f
125 N*M
75529N
Part Numbers:
75529, 87436
44570, 75156 UH
Max Tongue
WT
400 lb. (182 Kg)
400 lb. (182 Kg)
2
1
If
6-1-11
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 75529
Sommaire des Matières pour Cequent Performance Products 75529
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75529N 6-1-11 Rev. B 2007, 2011 Cequent Performance Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2007, 2011 Cequent Performance Products Feuille 2 de 3...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007, 2011 Cequent Performance Products Hoja 3 de 3 75529N 6-1-11 Rev.