Accessories; Wire Diagram - CAB CL.MD Livret D'instructions

1) DESCRIPTION
The CL.MC control unit is able to control 1 electromechanical tubular motor for electric sun shade curtains and
rolling shutters.

2) ACCESSORIES

The control unit can be equipped with the following accessories:
T4WV-C: 4-channel, rolling code transmitter.

3) WIRE DIAGRAM

Terminal Function
1,2 Phase, Neutral
3,4,5 Motor control
6 CLOSE push button
7 OPEN push button
8 Push buttons, common
RADIO Integrated radio module
4) OPERATION
To control the motor, use auto-default push buttons or buttons of the stable type.
Operation of push buttons: if the buttons are pressed for one second, the sun shade curtain moves in the requi-
red direction until it reaches the end of stroke set by the motor limit switch. If the stroke must be stopped before
time, press the button corresponding to the reverse movement direction.
Transmitter operation:
Button1 = CLOSE / Button3 = OPEN. If the stroke must be stopped before time, press the button corresponding
to the reverse movement direction.
5) PROGRAMMING FROM P1 PUSH BUTTON
Press push button P1 and keep it pressed for at least 3 seconds. When P1 is pressed, the buzzer will send a con-
tinuous sound, 1 second long. If P1 is kept pressed for more than 3 seconds, the buzzer will then send a continuous
sound, 5 second long. During this period of time, press the key of the transmitter to be stored in memory. If the
code memorization is successful, an intermittent buzz sound will be heard.
If the P1 button is NOT kept pressed for more than one second, the receiver switches to standard mode again.
Only the first transmitter code can be programmed by pressing the push-button. For the programming of the other
transmitter codes, please refer to paragraph 6: "How To Programme From Transmitter".
M
1
6) HOW TO PROGRAMME FROM TRANSMITTER
Every single transmitter is recognized by the control unit through a code, which is different from any other tran-
smitter. Each single code, therefore, must be stored in memory so that the control unit is able to recognize every
transmitter.
Op. Cl.
COM
Remote programming can be carried out on all control units which are placed within the transmitter range. It is
therefore recommended that only the control unit involved in programming be switched on during this step.
• How to memorize a new code with a transmitter already in memory:
1) press simultaneously both keys 1 and 2 of the transmitter already in memory;
the buzzer sends a continuous 5-second sound;
2) within 5 seconds, press a key on the receiver already in memory; the buzzer
stops the sound for one second and starts to buzz for other 5 seconds;
3) within 5 seconds, press a key of the new transmitter to be stored in memory;
If the code memorization is successful, an intermittent buzz sound will be heard.
• To erase a code via remote control:
1) press both keys 1 and 2 simultaneously, THREE TIMES, within 5 seconds;
the buzzer makes a slow, intermittent sound;
F2,5A
2) press a key on the transmitter to be erased; once it is erased, the buzzing stops.
7) HOW TO ERASE ALL TRANSMITTER CODES
Press button P1 three times, keeping it pressed for 10 seconds. The buzzer will make a fast, intermittent sound.
When the memory is entirely erased, the buzzer makes a continuous sound.
If the P1 button is NOT kept pressed for more than one second, the receiver switches to standard mode again.
CL.MD CONTROL UNIT
M M M
2 3 4
Op. Cl. Op. Cl. Op. Cl.
COM COM COM
Description
Control unit power supply, 230VAC 50Hz
Motor opening/closing controls:
- Close(3): CLOSE contact;
- COM(4): command, common;
- Open(5): OPEN contact.
Connection for closing push button
Connection for opening push button
Opening and closing push buttons, common
Receiver, 433.92 MHz
ALL JM1 JM2
a b c d e
Op. Cl.
COM
SP2
RT1
SW
ON
1 6
DL1
DL2
JM3 ANT
f g
R
A
Button 1
D
CLOSE
I
O
Button 3
OPEN
T4WV-C
Button 2
Button 4
25
Klux
12 32
Klux Klux
8 45
Klux Klux
0 50