Publicité
Liens rapides
Heater without bottom insulation
Résistance sans housse inférieure
Resistenza senza gancio
• Clean and degrease.
• Nettoyer et dégraisser.
• Pulire e togliere il grasso
Heater with bottom insulation
Résistance avec housse inférieure
Resistenza con gancio
Fig. 1
• Clean and degrease.
• Nettoyer et dégraisser.
• Pulire e togliere il grasso
Fig. 2
• Remove protection.
• Retirer la pellicule protectrice.
• Rimuovere la pellicola protettiva.
1 | © Danfoss | DCS (CC) | 2017.06
Instructions Surface Sump Heaters
Instructions Résistance de Surface
Istruzioni Resistenza carter
Compressor Model
DSH/SH/WSH090 to
DSH/SH/WSH184
SM112 to SM147
DSH/SH090 to
DSH/SH184
* As an optional heater for DSH/SH090 to DSH/SH184, 48W heater can only be used in the enclosed condition that
will not be accessible to wind, the minimum allowed ambient temperature is -5°C.
Fig. 2
Fig. 1
• Remove protection.
• Retirer la pellicule protectrice.
• Rimuovere la pellicola protettiva.
Compressor Model
SM/SZ084 to SM/SZ161
SM/SZ115 / 125 / 160
SM/SZ175 &
SM/SZ/SY185
SH180 & DSH/SH240 to
DSH/SH485
SY/SZ240 to SY/SZ380
Fig. 3
• Apply strongly and press to stick.
• Appliquer fortement et appuyer pour coller.
• Applicare e premere forte per incollare.
Surface Sump Heater
120Z0388
120Z0389
120Z0390
120Z0391
120Z0402
120Z0667
120Z0668
120Z0669
120Z0670
120Z0671
Surface Sump Heater
120Z0361
120Z0380
120Z0381
120Z0382
120Z0383
120Z0363
120Z0384
120Z0385
120Z0386
120Z0387
120Z0360
120Z0376
120Z0377
120Z0378
120Z0379
120Z0372
120Z0373
120Z0375
8510257P01-D
Resistance (Ω)
Voltage (V)
7.2
24
661
230
2000
400
2645
460
4133
575
12
24
1102
230
3333
400
4408
460
6888
575
• Apply strongly and press to stick.
• Appliquer fortement et appuyer pour coller.
• Applicare e premere forte per incollare.
Resistance (Ω)
Voltage (V)
12
24
1102
230
3333
400
4408
460
6888
575
12
24
1102
230
3333
400
4408
460
6888
575
10.3
24
955
230
2857
400
3778
460
5904
575
661
230
2000
400
4133
575
Fig. 4
• Put bottom insulation and fasten two pins.
• Mettre la housse inférieure et la maintenir
avec deux épingles.
• Mettere del materiale isolante e fissare con i
due clips.
FRCC.PI.009.A7.61
Output (W)
80
48*
Fig. 3
Output (W)
48
48
56
80
Publicité
Manuels Connexes pour Danfoss 120Z0388
Sommaire des Matières pour Danfoss 120Z0388
- Page 1 • Mettre la housse inférieure et la maintenir • Rimuovere la pellicola protettiva. • Applicare e premere forte per incollare. avec deux épingles. • Mettere del materiale isolante e fissare con i due clips. 8510257P01-D FRCC.PI.009.A7.61 1 | © Danfoss | DCS (CC) | 2017.06...
- Page 2 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trade- marks in this material are property of the respective companies.