Preparation For Use; Turn On The Un T For The F Rst T Me; To Add/De Ete Channe S - FUNAI SV2000 Manuel Du Propriétaire

Preparation for Use

Turn On the Unit for the
First Time
VCR VCR
VCR VCR VCR
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section.
2
2
STANDBY-ON
Remote Control
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
or
3
3
AUTO SET UP
Do you connect the cable from the cable box or
the satellite box to the unit's ANT-IN jack?
YES
Y es
Y es
Press [MENU]
to exit.
• Refer to "Hint for Cable Box or
Satellite Box" section on page 6.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized
in this unit by using [SKIP/CH. G G /K K H
(or [CHANNEL K K /L L ]).
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press [B] once again.
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using
the Number buttons or
.
[SKIP/CH. G G /K K H H /L L ]
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number. (For
example: 117, press [1], [1], [7])
• You must precede single-digit channel
numbers with a zero (for example: 02,
03, 04 and so on).
To Add/Delete Channels
1
1
MENU
or
TV Screen
2
2
[ON]
or
3
3
CH 01
or
4
4
or
NO
H /L L ]
5
5
To exit the
menu
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2) Select "CHANNEL SET UP" by pressing
[K K /L L ], then press [B].
3) Select "AUTO SET UP" by pressing
[K K /L L ], then press [B]. After scanning, the
tuner stops on the lowest memorized
channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Select "LANGUAGE SELECT" by pressing
[K K /L L ], then press [B].
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing [K K /L L ] , then press
[CLEAR/C.RESET].
Hint
Hint
• If you accidentally select Spanish or French
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
Clock Setup
• If the clock is not set, the
"CLOCK SET" screen
appears when you press
1
1
[MENU]. In this case,
press [MENU] again.
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
2
2
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
Select the channel to
be added or deleted.
3
3
MANUAL SET UP
CHANNEL 30 (CATV)
DELETE
Select "ADD" or "DELETE".
4
4
CLEAR/
C. RESET
5
5
– 8 –
and need English: Press [MENU] and
choose SELEC. IDIOMA or SELECTION
LANGUE. Press [B] and select ENGLISH.
Finally, press [CLEAR/C.RESET].
VCR VCR
VCR VCR VCR
- M E N U -
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
• If the clock is not set, the
CLOCK SET screen
or
appears when you press
[MENU]. In this case, go
to step 2).
CLOCK SET
MONTH DAY
1 0 / – –
or HOUR MINUTE
– – : – –
Select the current month.
CLOCK SET
MONTH DAY
1 0 / 0 3
or HOUR MINUTE
– – : – –
Select the current day.
CLOCK SET
MONTH DAY
1 0 / 0 3
or
HOUR MINUTE
– – : – –
Select the current year.
CLOCK SET
MONTH DAY
1 0 / 0 3 MON 2 0 0 5
or
HOUR MINUTE
0 5 : – –
Select the current hour.
YEAR
– – – –
AM/PM
– –
YEAR
– – – –
AM/PM
– –
YEAR
2 0 0 5
AM/PM
– –
YEAR
AM/PM
– –
EN