Auto Shut-Off - Bosch Sensixx B45L Notice D'utilisation

Masquer les pouces Voir aussi pour Sensixx B45L:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
en
In both cases, if you find that water is dripping out of the
soleplate, set the temperature selector (15) to a higher
position (take care that the garment can be ironed
on this heat temperature setting).
• At the beginning of each use, it is possible that drops
of water will be dispensed alongside steam.
Therefore, it is advisable to try the iron on the ironing
board or a piece of cloth to start with.
"Pulse steam" function
This appliance has a special function for tackling
difficult creases.
The "Pulse steam" function helps soften stubborn
garments like jeans or linen faster.
When the steam release button is activated, the steam
generator will give three powerful shots of steam so
that the steam reaches even deeper into the fabrics.
1. Set the temperature selector (15) on "• • •"
2. Press the steam release button (16) on the bottom of
the handle two times in quick succession (double-click)
or (model dependent)
Briefly press the steam release button (17*) on the
top of the handle.
Remarks:
• It is possible to stop the shots of steam by quickly
pressing the steam button again.
• Some water drops may appear when you use the
"Pulse steam" function for the first time.
The water drops will disappear after you have used
the function for some time.
Ironing without steam
1. Begin ironing but without pressing the steam release
button.
Vertical steam (C)
This can be used to remove creases from hanging
clothes, curtains etc.
Warning!:
• Never direct the steam jet at garments that are
being worn.
• Never aim the steam at people or animals.
1. Set the temperature to the "•••" setting.
2. Hold the iron in an upright position 15 cm away from
the garment being steamed.
3. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a
vertical position and pressing the steam release
button (16 or 17*).
"Intelligent steam" function
(model dependent)
This system has intelligent steam control, which, after
releasing the steam release button (16), provides a
small amount of additional steam.
The additional steam can always be stopped by briefly
pressing the steam release button once again.
12
Energy saving
button
(model dependent)
If the "Energy saving" button (8*) is switched on, you
can save up to 25% of the energy and 40% of the water
consumption (*), and still achieve good results when
ironing most of your garments.
It is advisable to use the normal energy setting only for
thick and very wrinkled fabrics.
(*) In comparison to the maximum setting.
Note: If you work with the "Energy saving" function,
the variable steam regulation and temperature
regulation can still be used as recommended.

Auto shut-off

(model dependent)
If during ironing, the steam release button (16-17*) on
the iron handle is not pressed for a certain length of
time (8 minutes), the steam station will automatically
switch off.
The "auto shut-off" pilot lamp (9) will flash when auto
shut-off has been activated.
To switch the steam station back on, press the steam
release button again.
Fabric protection soleplate cover (D)
(model dependent)
The fabric-protection soleplate cover (20*) is used
for steam-ironing delicate garments at maximum
temperature without damaging them. Use of the
soleplate cover also does away with the need for a
cloth to prevent shine on dark materials.
It is advisable to first iron a small section on the inside
of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip of
the iron into the end of the soleplate cover and pull the
elastic strap over the lower rear of the iron until it fits
tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabric-protection soleplate cover may be purchased
from our customer service or from our website:
Accessory code
(After-sales)
571510
Calc'n'Clean Advanced (E)
Cleaning the Boiler
To extend the life of your steam generator and to
prevent any build up of scale, it is essential that you
rinse out the filter (4*) and the boiler after several hours
of use. If the water is hard, increase the frequency.
Do not use descaling agents for rinsing out the boiler,
as they could damage it.
Name of accessory
(Online shop)
TDZ2045

Publicité

Table des Matières
loading

Table des Matières