MSW Motor Technics MSW-POL560C Manuel D'utilisation page 5

SYMBOLS
The operation manual must be reviewed.
Never dispose of electrical equipment together with household waste.
This machine complies to the CE declarations.
Protective goggles must be worn.
Ear protection must be worn.
Safety mask must be worn.
This is a device of the 2nd protection class with double insulation.
Drawings in this manual are for illustration purposes only and in some details it
PLEASE NOTE!
may differ from the actual machine.
The original operation manual is in German. Other language versions are translations from German.
GENERAL OPERATIONAL PRECAUTIONS
1. Keep the work area clean. Cluttered areas can cause injuries.
2. Consider the work area environment. Don't expose power tools to rain or wet soil. Don't use power
tools in damp or wet locations. The work area should be well protected. Don't use the tool in the
presence of flammable liquids or gases. Power tools produce sparks during normal operation or
when switching ON/OFF. Never use power tools in dangerous sites containing lacquer, paint, benzene,
thinner, gasoline, gases, adhesive agents, and other materials which are combustible or explosive.
3. Provide sufficient protection against electric shock. Prevent body contact with grounded surfaces, such
as for example: pipes, radiators, ranges and refrigerator enclosures.
4. Keep children and third parties away from the work area.
5. Store unused tools. When not in use, all tools should be stored in a dry and high or locked place, out
of the reach of children.
6. Do not overload the machine! To ensure an optimum in the performance and safety of the machine, it
should only be used within the set parameters.
7. Use only suitable tools. Don't use tool or attachment for tasks for which they are not intended. For
example: Don't use circular saw for cutting tree limbs or logs.
8. Dress properly. Do not wear loose clothing or jewelry. They can get caught in moving parts. Rubber
gloves and nonskid footwear are recommended when working outdoors. Wear protective hair
covering to contain long hair.
9. Wear protective goggles. Dust masks should be worn in dusty work.
10. Do not damage the connection cable. Never carry tool by cord or yank it to disconnect it from the
power source. Keep cord from heat and oil sources and sharp edges.
11. Secure the work area. It is recommended to use clamps or a vice for fixation. Please pay special
attention to your hands when operating the machine!
12. Do not overreach yourself. Keep proper footing and balance at all times.
13. Hold the machine firmly in both hands. When using the machine, hold it by the handles which are
provided with the machine.
14. Keep all tools in good condition. Keep the tools clean for better and safer performance. Follow the
instructions for lubricating and renewing the accessories. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean, and free from oil and grease.
15. Switch off the machine and disconnect the cable before maintenance or changing accessories (chisel,
drill, and knife).
16. Remove the adjusting keys and wrenches. Always make sure that keys and adjusting wrenches are
removed from the tool before turning it on.
8
U S E R M A N U A L
17. Avoid unintentional switching on of the device. Do not connect the device to the power supply and
18. When working outdoors only use extension cords intended for outdoor use.
19. Stay alert when operating the machine. Do not operate tool when you are tired.
20. Check damaged parts. Before further use of the tool, any parts of the casing or other parts that are
21. Do not use power tools for applications other than those specified in the instruction (other than
22. To ensure the designed operational integrity of power tools, do not remove installed parts of the
23. Do not touch movable parts or accessories unless the power source has been disconnected.
24. Use your tool at lower input load than specified on the nameplate to increase working efficiency and
25. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner, benzene, alcohol, ammonia
26. Consult an authorized service agent in the event of power tool failure.
27. Use only original replacement parts.
28. This tool should only be disassembled for replacement of carbon brushes.
29. When using the machine pay special attention to a recoil, which is a sudden reaction of the machine
30. The power cord should be kept away from the rotating parts of the machine.
31. Clean the machine's ventilation slots regularly.
PRECAUTIONS ON USING THE MACHINE
1.
2.
3.
4.
5.
6.
7.
8.
9.
Failure to follow safety recommendations and instructions may result in serious injuries or
death!
Rev. 16.06.2020 Rev. 16.06.2020
carry it with the fingers on the main switch. Make sure that the main switch is switched off while the
machine is being connected to the power source.
damaged should be carefully checked to determine that they will operate properly and perform their
intended function. Check for alignment of moving parts, mounting, and any other conditions that may
affect the machine's operation. A part of the casing or other part that is damaged should be properly
repaired or replaced by an authorized service centre unless otherwise indicated elsewhere in this
instruction manual. Defective switches should be replaced by an authorized service centre. Do not use
the tool if the switch does not turn it on and off.
those for which it was designed).
casing or screws.
decrease wear out.
and oil may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts
with a soft cloth lightly dampened with soapy water.
to the rotating disc blocking. As a consequence of blocking of the rotating tool, the machine tugs in
a direction opposite to the disc rotation direction. The recoil is a consequence of inappropriate use of
the machine.
Wear protective goggles to protect your eyes.
Wear earplugs to keep your ears noise-free while working.
Wear dust masks.
Pay attention to the correct adjustment of the grip.
The tool becomes very hot during operation.
Safe operation depends on one's work posture.
Wear protective shoes to protect your feet. Wear protective gloves.
To avoid injury from accidental starting, always remove the plug from the electrical socket before
installing or removing the disc, plate, or other removable accessories.
The machine should always be turned on/turned off at the lowest speed range (MSW-POL560C only).
9