Ryobi RY802800 Manuel D'utilisation page 13

WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result
in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instructions
could result in serious injury, electric shock, or death.
WARNING:
Risk of serious burns. Do not touch the muffler or
place any body parts in the path of hot exhaust gases,
which can cause burns and other serious personal
injuries.
NOTICE:
This product is not equipped with a spark arrestor and
cannot be used on U.S. forest lands; in addition, product
users must comply with Federal, State, and local fire pre-
vention regulations. Check with appropriate authorities.
Refer to accompanying engine manual for maintenance
and replacement parts.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
a qualified service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
 Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
 Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
 Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
All manuals and user guides at all-guides.com
OPERATION
ADDING/CHECKING ENGINE LUBRICANT
See Figure 7.
NOTE: This machine has been shipped with approximately
2 oz. of lubricant in the engine from testing. You must add
lubricant to the engine before starting it the first time.
To add engine lubricant:
 Place pressure washer on a flat, level surface. Do not tilt.
 Unscrew the oil cap/dipstick by turning counter-
 Before first use, squeeze the entire contents of the lubri-
 Replace the oil cap/dipstick and securely tighten.
To check engine lubricant level:
 Place pressure washer on a flat, level surface. Do not tilt.
 Unscrew the oil cap/dipstick by turning counter-
 Wipe dipstick clean and re-seat in hole; do not rethread.
 Remove dipstick again and check lubricant level. Lubricant
 If level is low, add engine lubricant until the fluid level rises
 Replace and secure the oil cap/dipstick.
ETHANOL-BLENDED FUELS
ADDING GASOLINE TO THE FUEL TANK
See Figure 8.
Page 9 — English
NOTICE:
Any attempt to start the engine without adding lubricant
will result in engine failure.
clockwise.
cant container provided into the oil reservoir.
After initial use, add 4-stroke engine lubricant (SAE 30 or
SAE 10W30) until the fluid level rises to the upper portion
of the hatched area on the dipstick. Do not overfill.
clockwise.
level should fall within the hatched area on the dipstick.
to the upper portion of the hatched area on the dipstick.
NOTICE:
Do not overfill. Overfilling the crankcase may cause ex-
cessive smoke and engine damage.
NOTICE:
Do not use E15 or E85 fuel in this product. It is a viola-
tion of federal law and will damage the unit and void
your warranty. Only use unleaded gasoline containing
up to 10% ethanol.
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.