Further Safety Instructions - Scheppach GS650 Traduction Des Instructions D'origine

• Store idle power tools out of children's reach. Do
not allow persons unfamiliar with the tool or these
instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
• Keep the power tools in good condition. Check
that moving parts are functioning smoothly and
do not lock, whether parts are broken or for any
other condition that may affect the power tool's op-
eration. If damaged, have the power tool repaired
before use. Many accidents are associated with
poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are
likely to block less and are easier to control.
• Use the power tool, the accessories, bits, etc. in
accordance with these instructions and in the man-
ner intended for the particular type of equipment.
Take into account the working conditions and the
work to be performed. Using power tools for op-
erations different from those intended can lead to
hazardous situations.
Service
• Have your electric tool repaired only by trained
personnel using only genuine spare parts. This will
ensure that your electric tool remains safe to use

5. Further Safety Instructions

• Connect the device only to a power point with a
residual current protective device (RCD) with a
measured residual current of not more than 30 mA.
• Keep the mains cable and extension cable away
from the grinding disk and saw chain. In the event
that it is damaged or severed, immediately discon-
nect the plug from the socket. Do not touch the
cable before it has been disconnected from the
mains. Risk of electric shock.
• The replacement of the plug or the connection line
must always be executed by the manufacturer of
the electric tool or his/her customer service in order
to avoid any hazards.
• Only switch the device on once it is safely fixed to
the worktop.
• For your own safety only use accessories and
attachments which were stated in the operating
instructions or recommended or specified by the
tool manufacturer.
• Only use grinding discs where the printed rotational
speed is at least as high as what has been speci-
fied on the name plate of the device.
• Carry out a visual inspection of the grinding disc
before use. Do not use any damaged or deformed
grinding discs. Replace any damaged or worn
grinding discs.
• Make sure that the sparks produced by grinding do
not present a danger, e.g. reach people or ignite
flammable substances.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
• Never keep the fingers between the grinding disc
and spark protection or in close proximity to the
protective hoods. There is a risk of crushing.
• The rotating parts of the device cannot be covered
due to functional reasons. Therefore, proceed cau-
tiously and hold the workpiece firmly in order to
avoid slipping which could cause your hands to
come into contact with the grinding belt or grind-
ing disc.
• The workpiece gets hot during grinding. Do not
touch the machined area, allow it to cool down.
There is a risk of burning. Do not use coolants or
the like.
• If you are tired or have consumed alcohol or tab-
lets, do not work with the device. Always have a
break on time.
• Switch the device off and remove the mains plug
– to loosen a blocked insertion tool,
– if the connection line is damaged or entangled,
– in case of unusual sounds.
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
• Lung damage if no suitable protective dust mask
is used.
• Damage to hearing if no suitable ear protection
is used.
• Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
GB | 19