Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-2561
π
H-2562
RECTANGULAR
PICNIC TABLE
TOOLS NEEDED
3/4" (19 mm) Socket Bit
3/8" (10 mm) Drill Bit (Included)
Power Drill
Base Support Board x 1
Figure 1
PAGE 1 OF 6
1-800-295-5510
uline.com
Tape Measure
Two Person Assembly
(Optional)
Plastic Base x 3
ASSEMBLY
PARTS
Slat x 5
4" Lag Screw x 30
NOTE: It is important to keep lag screws loose
throughout assembly. Tighten during step 8.
WARNING! Do not lean on tabletop or seats
when assembling.
1. Verify all parts are present before beginning.
2. Place the three plastic bases on a flat level surface
using the base support board to keep them straight.
You will attach this board in step 7. (See Figure 1)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Washer x 3
3½" Lag Screw x 3
0721 IH-2561
Publicité
Manuels Connexes pour Uline H-2561
Sommaire des Matières pour Uline H-2561
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2561 π 1-800-295-5510 H-2562 uline.com RECTANGULAR PICNIC TABLE TOOLS NEEDED 3/4" (19 mm) Socket Bit 3/8" (10 mm) Drill Bit (Included) Tape Measure Two Person Assembly (Optional) Power Drill...
- Page 2 3/4” socket bit. (See Figure 5) 8. Turn table right side up. Make sure the table is square and tighten all lag screws. NOTE: H-2565 Mounting hardware sold separately. Figure 5 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-2561...
-
Page 3: Herramientas Necesarias
H-2561 π 800-295-5510 H-2562 uline.mx MESA RECTANGULAR PARA PÍCNIC HERRAMIENTAS NECESARIAS Dado de 3/4” (19 mm) Broca de 3/8” (10 mm) (Incluida) Cinta de Medir Dos Personas para el Ensamble (Opcional) Taladro PARTS 1 Tabla de Base de Soporte 5 Tablas 3 Rondanas 3 Bases de Plástico... - Page 4 (Vea Diagrama 5) 8. Enderece la mesa. Asegúrese de que la mesa esté en escuadra y apriete todos los tornillos tirafondo. NOTA: La tornillería de instalación H-2565 se vende por separado. Diagrama 5 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-2561...
-
Page 5: Outils Requis
H-2561 π 1-800-295-5510 H-2562 uline.ca TABLE À PIQUE-NIQUE RECTANGULAIRE OUTILS REQUIS Douille tournevis de 19 mm (3/4 po) Ruban à mesurer Mèche de perceuse de 10 mm (3/8 po) (incluse) Montage à deux personnes (optionnel) Perceuse électrique PIÈCES Support de base x 1... -
Page 6: Montage Suite
3/4 po. (Voir Figure 5) 8. Remettez la table à l’endroit. Assurez-vous que la table est bien cadrée et vissez tous les tire-fonds. REMARQUE : Le matériel d’installation H-2565 est vendu séparément. Figure 5 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-2561...