KENMORE ELITE HE3 110.C9787 Serie Guide D'utilisation Et D'entretien page 22

Sécheuse à gaz
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Are fabric softener sheets blocking the lint screen grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
Is the exhaust vent diameter the correct size?
Use 4" (10.2 cm) diameter vent material.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. For most installations, the rear of the
dryer requires 5" (12.7 cm). See the Installation Instructions.
Has an air dry modifier been selected?
Select the right temperature for the types of garments being
dried. See "Modifiers."
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Maintenance Agreements
Your purchase has added value because you can depend on
Sears HomeCentral
®
for service. With over 2,400 Service
Technicians and more than a million parts and accessories, we
have the tools, parts, knowledge and skills to back our pledge:
We Service What We Sell.
®
Your Kenmore
product is designed, manufactured and tested to
provide years of dependable operation. But like all products, it
may require service from time to time. The Sears Maintenance
Agreement offers you an outstanding service program, affordably
priced.
22
All manuals and user guides at all-guides.com
MAINTENANCE AGREEMENTS
Cycle time too short
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Do not use a dryer rack with an Automatic Cycle.
Lint on load
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Stains on load or drum
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
Was the load removed from dryer at the end of the cycle?
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Odors
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
The Sears Maintenance Agreement
Is your way to buy tomorrow's service at today's price
Eliminates repair bills resulting from normal wear and tear
Provides phone support from a Sears technician on products
requiring in-home repair
Even if you don't need repairs, provides an annual Preventive
Maintenance Check, at your request, to ensure that your
product is in proper running condition.
Some limitations apply. For more information about Sears
Canada Maintenance Agreements, call 1-800-361-6665.

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

He3 110.c9789 serie

Table des Matières