Battery Charging; Know Your Product; Operation - RS 754-1927 Notice Originale

arm to To install the battery: Insert the charged battery (8) into
n, and the opening at the base of the power tool until the battery
is securely latched with a click.
packs
urces.

batteRy cHaRging

y kind.
▪ Insert the plug of the charger in the socket. The green
d area
LED on the charging indicator (9) will start to glow thus
indicating that the charger is in standby state.
pe and
▪ Insert the battery (8) in the charger socket (10) consid-
Check
ering the polarity.
eplace
▪ A new battery will work properly after five times of
charging and discharging. Charge and discharge a
battery, which is not used for a long time, for two to
a lamp
three times to function well.
▪ When the battery working time is remarkably short de-
ocation
spite full charging, the life of the battery may be over.
pproxi-
Replace the battery immediately.
he tool,
ervice
after 30 minutes, remove it from the charger after this
fails to
time.
easily
under
charging indication:
e.
▪ The green LED starts to glow upon plugging the
riously
charger in the mains.
battery
▪ The green LED ceases to glow and the red LED lights
up after the battery has been placed in the charger,
er use,
thus indicating the beginning of the charging process.
warm
▪ During the charging process the charger and battery
uninsu-
might become warm. This is a normal condition, and
does not indicate a problem.
▪ After completion of charging which takes approxi-
mately 30 min, the red LED ceases to glow and the
attery
green LED lights up.
e bat-
▪ The charger features thermal overload protection for
entre
the battery. Nevertheless we recommend withdraw-
ing the battery from the charger upon expiring of the
charging time. You may use additionally an electric
cHaR-
timer in order to control the charging time.
e at-
k fOR
tO Obtain tHe best life fOR tHe batteRy
▪ When battery is not in use, keep it away from other
upplied
Never metal objects like paper clips, coins, keys, nails,
ool and screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause fire or ex-
munici- plosion.
ged or ▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
pack charger in premises where the temperature may drop
under 0ºC or exceed +40ºC.
he bat-
of the
batteRy state inDicatiOn
The battery state during operation can be checked by
the LED display (4). To actuate the indicator press the
erse
ON/OFF trigger switch (5).
n the
3 = Battery 100% - 60% charged.
tool
2 = Battery 60% - 30% charged.
1 = Battery < 30% charged. It is necessary to recharge
the battery.
Original instructions
RS-754-1927-pages-GUR 10.8Li.indd 7
All manuals and user guides at all-guides.com
WaRning: The battery will be fully charged
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
VII - Know your product
Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Locking sleeve
2. Bit holder
3. LED work light
4. LED battery indicator
5. ON/OFF trigger switch
6. Forward reverse switch
7. Battery release buttons
8. Battery
9. LED charge state indicator
10. Charger
VIII - Operation
leD WORk aRea ligHt
The machine is equipped with LED light (3) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. The LED light is on until the ON/
OFF switch (5) is pressed.
ReveRsing
The extreme position of lever (6) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (5) is depressed lever (6) can not be
actuated. (Fig. 1)
WaRning: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
sWitcHing On - sWitcHing Off
switching on: press ON/OFF switch (5).
switching off: release ON/OFF switch (5).
The power tool is equipped with a brake. The spindle
stops rotating immediately after releasing the switch le-
ver.
smOOtH electROnic Rpm cOntROl
Light pressure on ON/OFF trigger switch (5) results in
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
7
EN
8.6.2012 . 15:14:58 .