Additional Safety Rules For Impact Drivers; Additional Instructions For Work With The Charger - RS 754-1927 Notice Originale

5. seRvice
t such
hat, or
a) Have your power tool serviced by a qualified
ditions
e the
ecting
icking
ols with
IV - Additional safety rules
er tools
before
key left
▪ Be aware that this tool is always in operating condi-
ol may
tion, because it does not have to be plugged into an
electrical outlet. Always set the trigger switch to the
nd bal-
locked OFF position when installing or removing the
ntrol of
battery pack.
▪ Wear ear protectors when impact drilling. Expo-
ing or
sure to noise can cause hearing loss.
gloves
▪ Hold power tool by insulated gripping surfaces
jewel-
only, when performing an operation where the
rts.
cutting accessory may contact hidden wiring or
ion of
its own cord. Cutting accessory contacting a "live"
s, en-
wire may make exposed metal parts of the power tool
used.
"live" and could give the operator an electric shock.
ed haz-
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
orrect
jury resulting from such cases of misuse.
correct
▪ To use this tool properly, you must observe the safety
at the
regulations, the assembly instructions and the oper-
ating instructions to be found in this Manual. All per-
does
sons who use and service the machine have to be
at can-
acquainted with this Manual and must be informed
us and
about its potential hazards. Children and frail people
must not use this tool. Children should be supervised
ource
at all times if they are in the area in which the tool is
er tool
being used. It is also imperative that you observe the
ng ac-
accident prevention regulations in force in your area.
reven-
The same applies for general rules of occupational
ng the
health and safety.
▪ The manufacturer shall not be liable for any changes
of chil-
made to the tool nor for any damage resulting from
ar with
such changes.
perate
▪ Even when the tool is used as prescribed it is not pos-
s in the
sible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool's con-
nment
struction and design:
parts
▪ Damage to hearing if effective ear defenders are not
ct the
worn.
ve the
cidents
V - Additional instructions
s.
operly
edges
ol.
ol bits
▪ Before using the charger, read all the instructions and
s, tak-
cautionary markings on the charger and battery pack
s and
as well as the instructions on using the battery pack.
er tool
▪ Only charge your batteries indoors as the charger is
could
designed for indoor use only.
Original instructions
RS-754-1927-pages-GUR 10.8Li.indd 5
All manuals and user guides at all-guides.com
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
for impact drivers
for work with the charger
WaRning: (For UK, Ireland, Cyprus or Malta
only):
Your RS cordless power tool is supplied with a char-
ger, which is fitted with a standard CEE 7/16" Euro
plug. In order for you to safely use this charger in the
UK, Ireland, Cyprus or Malta, you will need to fit the
enclosed converter plug. Not using the supplied con-
verter plug may invalidate the warranty.
The converter plug encapsulates an Euro plug, giving
a permanent/semi-permanent conversion to a British
plug. Please see instructions (Fig. 3) at the front of the
manual before fitting this converter plug.
▪ Place the adapter plug flat side down on the work sur-
face, using the correct screwdriver (either flat head or
Philips) unscrew the central retaining screw. Turn over
the adapter plug and carefully lift the cover of the plug
to reveal the inside of the adapter.
▪ Insert the 2 pin CEE 7/16 Euro plug into the retaining
clips of the adapter plug as shown on Fig. 3 and care-
fully close the cover of the adapter plug. Turn the plug
over, to reveal again the central retaining screw and
carefully tighten the screw, making sure the two sides
of the adapter plug fit together.
▪ Your adapter plug is now complete and is ready to
use in a BS 1363 electric socket as shown. Please
note you should never remove and type of plug from a
socket by pulling the cable, you should always remove
by gripping the plug itself.
WaRning: If the battery pack is cracked or
damaged in any other way, do not insert it in the char-
ger. There is a danger of electric shock.
WaRning: Do not allow any liquid to come
into contact with the charger. There is a danger of elec-
tric shock.
▪ The charger is not intended for any use other than
charging the exact type of RS rechargeable battery
pack as supplied with the charger. Any other use may
result in the risk of fire or electric shock.
▪ The charger and battery packs supplied with it are
specifically designed to work together. Do not attempt
to charge the battery pack with any other charger than
the one supplied.
▪ Do not place any object on top of the charger as it
could cause overheating. Do not place the charger
near any heat source.
▪ Do not pull on the lead of the charger to disconnect it
from the power source.
▪ Make sure that the charger cable is positioned where
it will not be stepped on, tripped over or otherwise
subjected to damage or stress.
▪ Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord
could cause the risk of fire or electric shock.
▪ Do not use the charger if it has been subjected to a
5
EN
8.6.2012 . 15:14:58 .