Mounting Instruction - RODCRAFT WP15 Mode D'emploi

EN
English
Technical Data (See figure 1.)
Dimension
capacity
[kg]
A
[mm]
B
[mm]
C
[mm]
F
[mm]
E
[mm]
F1
[mm]
F2
[mm]
R
[mm]
M
[mm]
oil
[l]
Weight
[kg]
max. pressure
[MPa]
All values are current as of the date of this publication. For the latest information please visit www.rodcraft.com.
Machine type(s)
• The machinery described is intended for machinery production and assembling spare parts. It is used to press, size, assemble, rivet small parts in
process No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.

Mounting instruction

Make sure every parts are fixed and tightened.
• Attach the base section and support to left and right connecting plate. (Fig. 04)
• Assemble the nylon ring to gauge fitting, then put the pressure gauge and twist tight. (Fig. 06)
• Remark: twist as tight as possible, otherwise it will be leak. Attach the gauge fitting to the suitable upper cross beam and twist bolt.
• Assemble pump to the frame. Fig. 07 (WP15), Fig. 09 (WP20S), Fig. 11 (WP30P & WP50P).
• Insert the complete handle into the opening of the lever support.
• During moving the machine, make sure to use the proper lifting equipment and follow the instructions as shows (Fig. 02).
Caution
Working area of 1 m must be kept free both in front of and behind the machine while it is in operation so that
it is always easily accessible.
Purge air from the hydraulic system:
• Open the release valve by turning it counterclockwise and purge the air bleed valve (Fig. 09)
• Pump several full stokes to eliminate any air in the system.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
Operation
Caution
Ensure table at proper position and lock the table by 4 pins firmly. (Fig.15)
• For WP15, WP30P and WP50P, Close the release valve and the control valve , by turning it clockwise.
Note : The 2-speed pump is switched for a fast approach.
For WP20S, Close the release valve, by turning it clockwise.
Note : WP20S has an Automatic 2-speed hydraulic pump, equipped with an automatic valve instead of an control valve.
• Pump the handle/foot pedal until serrated saddle nears workpiece.
Scale: 1:1 • Align workpiece and ram to ensure center loading. Document Ref: 8940169914_REV: 01 _ 05-2012
• For WP15, WP30P and WP50P, Close the control valve, by turning it Anticlockwise (slow position).
Note : The 2-speed pump is switched for a powerful pressing.
Caution
Caution : When applying the load (15 t, 30t or 50t), the control valve must be closed (slow position) to avoid
damage on system parts.
• Pump the handle/foot pedal to apply load onto workpiece (see numeration in pressure gauge).
• When work is done, stop pumping, slowly and carefully remove load from workpiece by turning the release valve counterclockwise in small increments.
(must turn with the small angle)
• Once ram has fully retracted, remove workpiece from table.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
The V-block must be used by pair, not by piece!
Only one person is allowed to operate the press.
Make sure that the operator must wear protective cloth, gloves, safety helmet, shoes and ear protector
during operating.
To avoid accidents, always be aware of any on-going work on the machine. Also, always stay focused on
the job to be done.
WP15 WP20S WP30P
15 000 20 000 30 000
700 740 795
540 700 700
882 1772 1772
120 132 140
500 510 535
157 185 151
457 1175 1031
160 186 160
/ / 200
0,6 0,95 1,1
75,5 105 166,7
61 69 58
WP15 / WP20S / WP30P / WP50P
WP50P
50 000
1030
800
1830
207
730
68
1048
200
245
2,5
298
62
Hydraulic press