Pingi CASCADA CHD-A4000M Mode D'emploi page 3

EN
CHD-A4000M - ULTRASONIC HUMIDIFIER
BOX CONTENT
HUMIDIFIER
CHD-A4000M
PARTS
Tank cover
Base
INTENDED USE
Your new Pingi Cascada humidifier CHD-A4000M is suitable for humidifying the air in enclosed indoor spaces.
The appliance operates on 220-240V, 50Hz (mains electricity). Never try to connect the device to other
power sources. Please always follow the safety instructions in this manual. Keep this instruction manual in
a safe place so that it is available at all times. This product complies with regulatory, national and European
requirements. Never try to make technical modifications to this device. We do not accept liability for accidents
or damages resulting from failure to follow these operating and safety instructions.
WHAT TO EXPECT
The Pingi Cascada humidifier CHD-A4000M is an ultrasonic humidifier that atomises water. High-frequency
vibrations transform up to 300 ml (±30ml) of water per hour into a fine mist. This means it will increase
the humidity level in the air by generating millions of small droplets. The device has a 4L tank. The CHD-
A4000M has multiple speed settings and can automatically maintain the ambient humidity level you select.
Humidifiers need to be cleaned regularly to prevent limescale build-up or biofilm formation. Please refer to the
cleaning section for further information.
BEFORE YOU START
Please carefully read the safety instructions on the front page of this manual before getting
started.
PLACEMENT AND INSTALLATION
1. Select a level surface that provides sufficient distance between the humidifier and any walls and other
objects. Please mind that some water may escape from the base or tank when installing the tank. Do not
place the device on or near moisture-sensitive objects or surfaces.
2. If needed, install the included filter cartridge in the appropriate slot in the base.
3. Plug in the device.
We recommend using this appliance in rooms with a room temperature of 18 - 22 °C
INSTRUCTION
MANUAL
Mist nozzle
Water
tank
Indicator LED
Control
dial
FILLING THE TANK
1. Empty and flush the tank. Then fill it with cold tap water. The tank can hold up to 4L of water.
2. Place the filled tank on the base and replace the tank cover.
3. You can change the direction of the mist output by rotating the mist nozzles.
4. You can add water at any time without removing the tank from the base.
SWITCHING ON THE HUMIDIFIER
The humidifier can be switched on and off with the control dial. After switching on the appliance, the
indicator LED will become green and the device will start to emit humidity. Use the dial to select the desired
power setting and to switch off the appliance. Selecting a higher power level will increase the amount of mist
produced.
OUT OF WATER SIGNAL
The humidifier will automatically switch off when it detects that the tank is empty. The indicator LED will turn
red when the tank is empty. Fill the tank to resume operation. The indicator LED will become green.
CLEANING
Both the tank and base need to be cleaned regularly.
We recommend cleaning the appliance once a week.
Important notices:
- Make sure the device is unplugged when cleaning it.
- Do not pour hot water in the tank.
- Do not use detergents or chlorine.
- Use vinegar or a coffee machine descaling fluid.
Procedure:
Water tank: Empty out the water tank. Rinse the water tank with cold water and some vinegar (1 cup).
Optionally use a soft brush. Thoroughly flush the tank after emptying out the vinegar solution.
Base: Empty out the base. Use a microfibre cloth with some cold water to clean it.
Filter cartridge: Rinse the filter cartridge with hot water. Optionally soak the filter several minutes in hot
water.
Ultrasonic element: The ultrasonic element is located in the base. Over time limescale deposits may become
visible on and around this element. If you notice this, it may require descaling. Empty out the base and
pour a mixture 1 part water and 1 part vinegar in the base. Wait for at least 30 minutes before pouring out
the vinegar. You may use a soft brush. Do not use hard brushes or tools, as this may damage the ultrasonic
element. Thoroughly rinse the base before switching on the appliance again.
Exterior: If necessary, wipe off the exterior of the appliance with a lightly dampened cloth.