Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION INSTRUCTIONS
E-GSD Series
MOUNTING USING SURFACE CONDUIT
1.
Loosen (2) screws on front cover and open cover.
2.
Disconnect two halves of the quick disconnect attaching the output
leads of the driver to the front cover.
3.
Open the cover to approximately a 45° angle. Remove cover from
back housing by sliding cover along axis of hinges. Set cover
aside for later use.
Remove 1/2" plug from side of fixture conduit will be fed from.
4.
Attach 1/2" conduit to chosen opening. Teflon tape should be used
on conduit threads to prevent water entry.
5.
Fixture is best mounted by drilling through (4) drill point locations
in corners of back housing. Housing is to be secured to mounting
surface using appropriate mounting hardware for the surface.
Mounting hardware supplied by others. Any unused holes in back
surface must be plugged. A high grade caulking material, such
as silicone rubber, should be used around all mounting holes to
prevent water entry.
Splice supply leads to fixture leads per Electrical Connections
6.
section.
7.
Replace front cover by reversing sequence followed in Step 3.
8.
Attach clip on end of safety cable on front cover to hole in driver
mounting bracket.
9.
Reconnect the two halves of the quick disconnect that were
disconnected in Step 2.
10. Close cover, being careful not to pinch any leads or the safety
cable, and tighten the screws loosened in Step 1.
ELECTRICAL CONNECTIONS
Fixture is equipped with universal volt driver 120-277V
(ie. 120V, 208V, 240V or 277V)
PHASE TO NEUTRAL WIRING 120/277V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no wires
are pinched.
PHASE TO PHASE WIRING 208/240V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no wires
are pinched.
DIMMING
1. Grey or pink (-) and violet (+) leads are for 0-10V dim-
ming systems. Cap off if not used.
2. For dimming connections, use Class 1 wiring methods.
www.e-conolight.com
|
Document:
LPN00852X0001A0_A
Created By:
TMT
CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved could void
your authority to use this equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
CAN ICES-005 (B)/NMB-005 (B)
888.243.9445
|
FAX: 262.504.5409
Date
ECO#
FCC NOTICE
3-29-2021
012560
Publicité
