Controlling A Tv With The Remote; Troubleshooting - Samsung DVD-S221 Mode D'emploi

Controlling a TV with the Remote

(DVD-S321 only)
The remote can also be set up to control most TVs. To program the remote, use the code
that corresponds to your brand.
Code Brand
01 SAMSUNG_1
02 SHARP_2
03 SONY
04 MAGNAVOX
05 SANYO_1
06 LG_2
07 RCA
08 LG_1
09 TOSHIBA
10 HITACHI
11 JVC
12 PANASONIC_1
13 MITSUBISHI_2
14 SAMSUNG_2
15 SAMSUNG_3
1
1
Turn on the TV
2
2
Point the DVD's remote at the TV.
3
3 While holding the TV POWER button
down, enter the code for your brand.
e.g
For Samsung_1 TVs
While holding down the TV POWER button,
enter 0 and then 1.
46
TV Codes
Code Brand
16 SHARP_1
17 ZENITH
18 LG_3
19 DAEWOO_8
20 SANYO_2
21 EMERSON
22 SHARP_3
23 SAMSUNG_4
24 PANASONIC_2
25 NOBLEX
26 TELEFUNKEN
27 NEWSAN
28 LOEWE
29 RCA2
4
4
If the TV turns off, setup is complete.
Enter other codes of the same brand if
the first code does not work.
5
5
To operate the TV, use the "TV Function
Buttons" described on page 19.
NOTE
The remote may not be able to control every
model TV of the brands listed.
Before requesting service (troubleshooting), please check the following.
Problem
• Check the batteries in the remote. May need replacing.
No operations can be
• Operate the remote control at a distance of no more than 20 feet.
performed with remote.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try remote again.
• Ensure that the disc is installed with the label side facing up.
Disc does not play.
• Check the region number of the DVD.
5.1 channel sound is not
• 5.1 channel sound is reproduced only when the following conditions
being reproduced.
are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the "Dolby 5.1 ch" mark on
the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
The icon appears on
• The features or action cannot be completed at this time because:
screen.
1. The DVD's software restricts it.
2. The DVD's software doesn't support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You've requested a title or chapter number or search time that is
out of range.
Disc Menu doesn't appear.
• Check if the disc has a Menu.
Play mode differs from the
• Some of the functions selected in the Setup Menu may not work
Setup Menu selection.
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot be
• The Screen Ratio is fixed on your DVDs.
changed.
• Make sure you have selected the correct Digital Output in the Audio
No audio.
Options Menu.
Forgot password • Press power on from a cold start with no disc in the unit. Press the STOP
and PLAY buttons simultaneously on the front panel for three seconds. The
Select Menu Language display will appear. Select the desired language
button. Press the SETUP button on the remote control to select the Parental
Mode. The Parental Mode is now unlocked as indicated on the display.
Press the DOWN button to select Parental. Press ENTER and the Create
Password display will appear. You can now set your rating level and
change your password to a new number.
If you experience other • Go to the contents and find the section of the instruction book that
problems. contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.

Troubleshooting

Action
Page
P6
P9
P20
P23
P40~41
P40~45
P45
P44
P43
47