Télécharger Imprimer la page

SawStop CNS-SFA Manuel D'utilisation page 3

Ensemble de clôture pour entrepreneur

Publicité

Déballage de votre ensemble de clôture
Lors du déballage de votre ensemble de clôture, vérifiez que tous les composants illustrés sur cette page sont
inclus. Faites attention lorsque vous déballez votre ensemble de clôture pour éviter d'endommager les composants.
rail arriere gauch
support à tablette de matériau
cloture
rail avant
grand crochet
de rangement
(deux)
SawStop
Contractor Fence Assembly
OWNER'S MANUAL
le manuel du
propriétaire
poignée de clÔture
®
pack matériel #3
Installing Your SawStop Contractor Fence Assembly
®
Installing the Fence Rails
Remove eight M8 x 20 square head screws
hardware pack and slide the square head of each screw into the
Assembly
slot along the rear edge of the front rail.
• Locate the front rail, the left and right rear rails, and hardware
pack #3. All of the hardware needed to install the rails is located
on hardware pack #3. In order to easily identify the hardware
used in each of the following steps, the different pieces of
hardware are numbered on the hardware pack and in the figures.
If you are missing hardware pack #3 or any of the other fence
assembly components, call the SawStop Service Department at
503-682-6222 for replacements.
Hardware Pack
#
3
Installing the Fence Rails
You will also need the following tools
Hardware for Steps 1-10
to complete the fence assembly:
1. two 13 mm wrenches
Square Head Screws, M8 x 20
(10 + 1 extra)
16
2. a level or straight-edge
Lock Washers, M8
3. a rubber hammer or mallet
(22 + 1 extra)
17
1
2
(18 + 1 extra)
Hex Nuts, M8
18
Hex Screws, M8 x 16
Carriage Bolts,
(8 + 1 extra)
19
M8 x 20 (4)
20
19
19
• Repeat the same procedure to mount the right rear rail (the
17
longer rail) to the rear of the table and to the right extension
17
19
wing. Again use three M8 x 16 hex screws
washers
screws; do not fully tighten them. The right rear rail should
extend beyond the right extension wing.
19
17
18
• Mount the left rear rail (the shorter rail)
to the rear of the table and to the left extension
wing using three M8 x 16 hex screws
19
, three
M8 lock washers
17
, and one M8 hex nut
. Insert one hex
18
screw into the hole in the extension wing and then use a lock
washer and hex nut to hold the screw in place, as shown. The
5
6
other two hex screws thread into corresponding holes
in the cast iron table. Place a lock washer on each
screw before threading them into the holes. Hand
tighten the hex screws; do not fully tighten them.
affiche des instruc-
tions d'installation
Ensemble de clôture pour entrepreneur SawStop 1
rail arriere droite
petit crochet
de rangement
(deux)
Hardware Pack
#
3
Installing the Fence Rails Assembly
Hardware for Steps 1-11
Square Head Screws, M8 x 20
16
(10 + 1 extra)
Lock Washers, M8
17
(22 + 1 extra)
Hex Nuts, M8
18
(18 + 1 extra)
Hex Screws, M8 x 16
Carriage Bolts,
19
20
(8 + 1 extra)
M8 x 20 (4)
SawStop Service Department
503-682-6222
www.sawstop.com
© SawStop, LLC
from the
• Place an M8 lock washer
17
and thread an M8 hex nut
18
16
the back of each of the eight square head screws, but do not fully
tighten the nuts at this time. Position the front rail so that the left
end of the rail extends about ⁄ inch past the edge of the left
3
4
extension wing.
16
• Adjust the position of each square head screw so that all eight
17
screws align with the corresponding mounting holes in the front
18
16
edge of the table top and extension wings. Position the front rail
3
4
against the edge of the table with the eight screws
extending through their corresponding mounting holes.
Make sure the rulers on the front rail are facing up.
• Locate the material support shelf, the two large storage hooks,
straight-edge
the two small storage hooks, and hardware pack #3. All of the
hardware needed to assemble the material support shelf is
19
, three M8 lock
17
, and one M8 hex nut
18
. Hand tighten the hex
located on hardware pack #3. Take the material support shelf
and insert two M8 x 20 square head screws
16
into the holes on
one end. Place an M8 lock washer
17
and a M8 hex nut
18
the back of each screw, but do not tighten the nuts.
19
19
17
16
17
Hardware Pack
#
3
Installing the Fence Rails
Hardware for Steps 1-10
17
18
Square Head Screws, M8 x 20
16
(10 + 1 extra)
Lock Washers, M8
17
17
(22 + 1 extra)
18
• Use a straight-edge to level the rear edge of the left extension
Hex Nuts, M8
18
(18 + 1 extra)
wing to the cast iron table top. You may have to pull up or push
Hex Screws, M8 x 16
19
Carriage Bolts,
20
down on the outer edge of the extension wing to level it. Once the
7
8
(8 + 1 extra)
M8 x 20 (4)
rear edge of the left extension wing is level, use 13 mm
wrenches to fully tighten the hardware that mounts the
left rear rail. Repeat this process to level the rear edge
of the right extension wing and secure the right rear rail.
on
on

Publicité

loading