Aritech ACL599 Manuel De Programmation page 5

E E E E E
RASING RASING RASING MODE RASING RASING
E E E E E PIN PIN PIN
PIN PIN
RASING ALL RASING RASING ALL ALL ALL CODES OR CODES CODES
RASING RASING ALL CODES CODES
Deletes all codes/cards. Deletes all codes/cards. Deletes all codes/cards. Deletes all codes/cards. Deletes all codes/cards.
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Press"8" followed by "99".
3. 3. 3. 3. 3. Press the " " button.
4. 4. 4. 4. 4. To leave the program, press
the "#" button.
E E E E E
RASING ONE RASING RASING ONE USER ONE ONE USER NUMBER USER USER NUMBER NUMBER NUMBER
RASING RASING ONE USER NUMBER
Deletes one code/card. Deletes one code/card. Deletes one code/card. Deletes one code/card. Deletes one code/card.
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Press "9".
3. 3. 3. 3. 3. Enter the user number,
which must be a two-digit
number between 01 and 99
(for example, user code 2 is
"02").
4. 4. 4. 4. 4. Press the " " button.
5. 5. 5. 5. 5. To leave the program, press
the "#" button.
A A A A A
SSIGNING SSIGNING THE THE
SSIGNING THE SSIGNING SSIGNING THE THE
1. 1. 1. 1. 1. Press "0".
2. 2. 2. 2. 2. Enter Engineeringcode "00".
3. 3. 3. 3. 3. Enter new Engineering
code. The code must be
between 1 and 8 digits.
4. 4. 4. 4. 4. Confirm the code by
pressing " ".
5. 5. 5. 5. 5. To leave the program, press
the "#" button.
Example of programming Engineering code 123456: Example Example Example Example
Press 0 00 123456 #
C C C C C E E E E E
HANGING THE HANGING HANGING HANGING HANGING THE THE THE THE NGINEERING CODE NGINEERING NGINEERING NGINEERING NGINEERING
1. 1. 1. 1. 1. Disconnect the keypad from
the power supply.
2. 2. 2. 2. 2. Place jumper J1 in "ON"
position. Refer to the
Connections picture.
3. 3. 3. 3. 3. Reconnect the keypad to the
mains.
4. 4. 4. 4. 4. Switch jumper J1 back to
"OFF" position.
5. 5. 5. 5. 5. Assign the Engineering
code.
MODE MODE MODE MODE
OR OR CARDS OR CARDS CARDS CARDS
OR CARDS
The yellow LED lights up and a long
beep sounds.
On every keystroke a short beep and
a long beep sound.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
The yellow LED lights up and a long
beep sounds.
A short beep sounds after every
keystroke.
A short beep sounds after every
keystroke.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
E E E E E
NGINEERING NGINEERING CODE CODE
NGINEERING CODE NGINEERING NGINEERING CODE CODE
Two short beeps are emitted by the
ACL599 keypad.
The yellow LED on the ACL599
keypad goes out.
CODE CODE CODE CODE
The yellow LED on the ACL599
keypad lights up, followed by several
beeps.
Attention: Attention: Several beeps indicate that you have done the wrong Attention: Attention: Attention:
keystrokes or actions.
A A A A A / / / / /
RM RM DISARM DISARM
RM RM RM DISARM DISARM DISARM FUNCTION
The arming and disarming function only works when the ACL599 is
combined with a slave ACL700 proximity reader and cards or keyfobs.
P P P P P / / / / /
ROGRAMMING ROGRAMMING ARM ROGRAMMING ROGRAMMING ROGRAMMING ARM ARM ARM ARM DISARM DISARM DISARM DISARM DISARM FUNCTION
First program card users or keyfob users as described earlier. See:
"Programming a card or a keyfob."
A A A A A / / / / /
SSIGNING SSIGNING AN SSIGNING AN ARM AN AN ARM ARM ARM DISARM DISARM DISARM FUNCTION
SSIGNING SSIGNING AN ARM DISARM DISARM
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Press "4".
3. 3. 3. 3. 3. Enter the user number,
which must be a two-digit
number between 01 and 99
(for example, user code 2 is
"02").
4. 4. 4. 4. 4. Enter "1" to activate the arm/
disarm function for this user
number. Then enter "0" to
deactivate the arm/disarm
function for this user
number.
5. 5. 5. 5. 5. Press the " " button.
6. 6. 6. 6. 6. To leave the program, press
the "#" button.
P P P P P
ROGRAMMING ROGRAMMING
ROGRAMMING ROGRAMMING ROGRAMMING AN
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Press "7".
3. 3. 3. 3. 3. Assign the relay to the exit
button:
Press "1" for relay 1
Press "2" for relay 2
Press "1" and "2" for
both relays
4. 4. 4. 4. 4. Press the " " button.
5 5 5 5 5 . To leave the program, press
the "#" button.
L L L L L
EA EA VING VING THE THE PROGRAM PROGRAM
EA EA EAVING VING THE VING THE PROGRAM THE PROGRAM PROGRAM
To leave the program at any time,
press the "#" button.
FUNCTION FUNCTION
FUNCTION FUNCTION
FUNCTION TO FUNCTION FUNCTION FUNCTION TO TO TO TO A A A A A USER USER USER USER USER
FUNCTION FUNCTION TO FUNCTION TO TO TO A A A A A USER USER USER USER
FUNCTION TO USER
The yellow LED lights up and a long
beep sounds.
A short beep sounds.
A short beep sounds after every
keystroke.
Two short beeps sound on the
keypad and on the reader. Relay 2
will be activated if a card or keyfob
is presented for +/- 3 seconds in
front of the proximity reader. If relay
2 is activated, relay 1 will be
blocked.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
AN AN EXIT EXIT BUTTON BUTTON
AN AN EXIT EXIT EXIT BUTTON BUTTON BUTTON
The yellow LED lights up and a long
beep sounds.
A short beep sounds.
A short beep sounds after every
keystroke.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
The yellow LED on the ACL599
keypad goes off and a short beep
sounds.
GB GB GB
GB GB
5