Electrolux AEF 3640 X Mode D'emploi page 5

page de 8

/ 8
Signets

Les langues disponibles

Introduction

Read this instruction manual carefully before installing the hood. These instructions are designed to tell you of the

various technical details of your cooker hood and to make you familiar with its use. Since these instructions cover more

than one type of hood within the same series, it may be that reference is made to components that do not form part

of the hood that you are installing. The hood may be used as an exhaust or filter hood. If evacuation is available (exhaust

duct or air flue) we recommend using the hood in the exhaust version to discharge all the kitchen vapors and odors

out-doors. Fittings can vary from country to country. We reserve the right to modify the product without any notice

always with the aim of improvements and in compliance with the relevant norm.

Suggestions for using the hood in exhaust position

When an exhaust hood and a heat source requiring ambient air (e.g. gas, oil, coal stoves, etc.) are used at the same

time, attention is required because the air necessary for combustion is exhausted from the room through the hood and

this creates depression. There is no such danger when the maximum depression in the room is 0,04 mbar. In this

condition no exhaust gas from the heat source is piped. To assure this condition, make openings in the room which

cannot be closed (doors, windows, etc. are not sufficient) and through which the air necessary for combustion can freely

flow.

Note:—All the exhaust ductwork in the apartment or house should be studied. In case of doubts, get advice or

authorization from the person or agency responsible for the building. When using gas burners, gas ovens, etc. as well

as when using the hood in the filter version, these precautions are not necessary.

N.B. The efficiency of the exhaust hood decreases as the length of the ducts and number of elbows increase. When

using the exhaust version, follow these rules: Do not connect the exhaust hood to chimneys, flues, and air ducts serving

the room. Before venting into exhaust flues and ducts no longer in use, ask for the approval of the person or agency

responsible for the building. The evacuated air must not be let into a warm air duct. For the evacuation of the exhausted

air please note ufficial instructions.

Installation

The hood must be mounted over the center of the cooking area. The minimum distance between the cooker and the

bottom of the hood must be 650 mm for electric cookers and 750 mm for gas cookers.

Warning: If the room contains a flued fuel burning appliance which is not of the "balance flue" type make sure these

is an adequate air inlet to the room at all times so that fumes are not drawn down the flue.

N.B. The distances, however, are subject to the safety rules in effect in the various countries. Before drilling the wall

make sure that no pipes or cables will be damaged. If there is no outer waste-pipe for the exhaust version, an air outlet

with a diameter of 130 mm must be made through the wall.

Wall fixing of the cooker hood

1) Set the distance between the cooker hob and the hood (Fig. 4).

2) Be careful, using the drilling template, to allow the correct minimum distance between the cooker and the bottom

of the hood, in particular when ducting to the outside using a pipe passing above the kitchen wall units (Fig. 6).

3) Join the two parts of the flange (Fig. 5/H) using the two screws, and apply the flange to the top of the motor unit

(Fig. 5/L), using 4 screws (Fig. 5/I).

4) Drill the holes in the wall to fix the hood, then fix the hood using the two screws and wall plugs (Fig. 5/N).

5) For a correct installation the hood is provided (in the rear side of its body) with one or two holes 8 mm diam. into

which one or two wall fixing screws must be inserted (Fig. 5/O).

6) Ducting version with pipes over wall units: join the two parts of the 90° curve (Fig. 5/G) using the screws, and

connect the curve to the flange. Connect the extension (Fig. 6/1) and turn the curve until it is pointing in the direction

required for ducting. Now connect up the extraction pipes.

7) Ducting version with extraction pipes: connect the flange to a pipe ducting to the outside.

8) Re-circulation version: see point 6), but close the pipe openings using the special plastic grids provided (Fig. 5/

S), making sure that the flow of air is directed upward and not towards the wall.

Insure that all parts are properly fixed and that it is impossible to touch moving parts.

N.B.: If the appliance is provided with a 150 mm spigot, please do not fix the exhaust tube by means of screws onto

the spigot, otherwise the no-return valve could not work proper.

Installation of the pipes

(valid for exhaust or filter version)

1) Fix the bracket (Fig. 5/C) with 2 plugs and screws (Fig. 5/A) in the required hight for the pipe.

2) Screw the short pipe (Fig. 5/D) with 2 screws on the bracket (Fig. 5/B).

3) Fit the long pipe from the front (Fig. 5/E).

4) After inserting the nuts into their housings, fix the long pipe to the hood using the two self-threading screws and

working from the inside (Fig. 5/Q).

5) Close the pipe openings using the special plastic grids provided (Fig. 5/S), making sure that the flow of air is

directed upward and not towards the wall.

N.B.: Make sure the supply voltage ratings correspond with those stated on the appliance data plate.

Attention: if the appliance is not provided with a plug or cannot be easily connected to a wall socket, then the electrical

circuit must incorporate a circuit breaker having at least a 3 mm separation between contacts.

Attention: This appliance must be connected to a system equipped with earth or ground plate. The manufacturers

decline responsibility for problems caused by failure to observe this rule. The wires in the supply cord are colored as

follows:

blue = neutral

—

brown = line

Using the cooker hood

The cooker hood should be switched on either before or at the same as cooking or frying commences. The grease

and carbon filters are more effective if the fan is not switched off immediately after cooking or frying is completed, but

only after a period of some 20-30 minutes. Before using the cooker hood please ensure that all plastic films like on

metal grease filter an stainless steel ducting are removed.

User instructions

Working instruction of the cooker hood

The cooker hood could be supplied with different operation panels (Fig. 3A-3B) that works in the following way:

Back Lit Switches HR (Fig.3A)

- Main Switch

1-2-3 Speed Switches

The Timer will run if any speed switch is pushed for more than 3 seconds and will stop running the cooker hood after

5 minutes.

Multicolour Switches HI (Fig.3B)

0/1-2-3 Speed Switches

L - Light Switch

The Timer will run if the timer switch is pushed and will stop running the cooker hood after 5 minutes.

Operation light and function of saturation indication for the filters

HI (Fig. 3B) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood and

pushing the bottom T the operation LED will indicate different colours with following meanings:

Green Light: less than 6 working hours

Yellow Light: between 6 and 12 working hours

Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)

HR (Fig. 3A) - The saturation of the grease filter will be indicated automatically after 20 hours by means with flashing

of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual changed.

It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 1

and 3 temporary for more than 2 seconds:

- No flashing light of the bottom: less than 6 working hours

- Flashing light of bottom 1: between 6 and 12 working hours

- Flashing light of bottom 1 and 2: between 12 and 18 working hours

- Flashing light of bottom 1, 2 and 3: more than 18 working hours

After you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the main

switch for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes

automatically the Timer.

If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the charcoal

2 - Light Switch

T - Timer

filter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal filter should be

replaced.

It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 2

and 3 temporary for more than 2 seconds:

- No flashing light of the bottom: less than 30 working hours

- Flashing light of bottom 1: between 30 and 60 working hours

- Flashing light of bottom 1 and 2: between 60 and 110 working hours

- Flashing light of bottom 1, 2 and 3: more than 110 working hours

After you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more than

2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the Timer.

Setting from Exhaust method into Filtering method (only for model HR - Fig.3A)

To get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting the

cooker hood into the proper method the electronic will adjust automatically the fan speed to the air resistance of the

charcoal filter.

Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the

cooker hood will set to the exhaust method - confirm by flashing all buttons for 4 times.

Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood will

set to the filtering method - confirm by flashing all buttons for 8 times.

Note: The cooker hood is set from the factory into the Exhaust method.