SIOUX GO459 Serie Manuel D'instructions Et Pièces Détachées page 3

Be aware of hazards in you workspace.
Slips, trips and falls are a major cause of workplace injury. Be aware of slippery surfaces caused by use of the tool and also of
trip hazards caused by the air or hydraulic hose. The sander is not intended for use in potentially explosive atmospheres and is
not insulated against contact with electric power. Ensure that there are no electrical cables, gas pipes, etc. which can be cause
a hazard if damaged by use of the tool. Never direct air at yourself or anyone else.
Your workplace may contain hazards that cause injury.
When disposing of a tool, do it in a way that does not harm personnel or the environment.
INTENDED USE
This tool is intended to be used with abrasive sanding discs for the finish sanding of materials such as wood, metal, fiberglass and similar materials. If it is
used for anything else, it is considered misuse, creates a hazard and may void the warranty.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an airline filter, pressure regulator, and
lubricator is recommended. Before connecting to tools, blow out the airline to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8" (10mm)
I.D. The tool inlet thread is 1/4" NPT.
LUBRICATION
For maximum performance and tool life, an airline lubricator, set to deliver 1 drop per minute. SIOUX No. 288 Air Motor Oil is recommended. If an airline
lubricator is not used, add 8 to 10 drops of air motor oil to the air inlet at the start of the day and run the tool for 10-20 seconds.
Do not over lubricate because excess oil may contaminate the surface being sanded.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. After long idle periods, flush the tool with a few drops of oil and run for 10
seconds. This will help remove contaminants and reduce the formation of rust.
OPERATION
Speed of the tool may be adjusted by turning the regulator located on the handle.
INSTALLING BACKING PADS
• Center pad on gear seat.
• Secure with 6 hex screws.
INSTALLING SANDING DISC
• PSA
Remove backing paper from sanding disc.
Center on backing pad and apply firm pressure.
• HOOK and LOOP
Center sanding pad on backing pad and apply firm pressure.
REMOTE VACUUM OPERATION
Attach vacuum hose from portable dust collection system to sander's vacuum swivel.
Weight
Catalog No.
(lbs/kg)
GO459-60SNP 4.4/2
GO459-60SNH 4.4/2
GO459-80SNP 4.4/2
GO459-80SNH 4.4/2
GO459-60SRP 4.4/2
GO459-60SRH 4.4/2
GO459-80SRP 4.4/2
GO459-80SRH 4.4/2
ZCE796
Form
Disconnect tool from air supply before installing or removing wheel or making any adjustments
Be sure the pad is the correct size for the tool.
A mismatch between tool and pad will cause excessive vibration.
SOUND AND VIBRATION READINGS
Sound Power
Sound Pressure
dBA
(per EN ISO 15744)
(per EN ISO 15744)
80
80
TBD
TBD
TBD
TBD
TBD
TBD
WARNING
WARNING
Uncertainty
dBA
(dBA)
91 3
91 3
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
3
Vibration m/s 2
Uncertainty m/s
(per EN 12096)
(per EN ISO 28927-3)
5.9
5.9
TBD
TBD
TBD
TBD
TBD
TBD
2021August2/E
Date
2
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD