Publicité
Les langues disponibles
Les langues disponibles
oof Brushed Speed Controller (RTR Version)
ng our electronic speed controller(ESC). The power system for RC model can be very
ead this manual carefully. In that we have no control over the correct use, installation,
ESC Operation
enance of our products, no liability shall be assumed nor accepted for any damages,
ting from the use of the product.
Thanks for purchasing our electronic speed controller(ESC). The power system for RC model
can be very dangerous, please read this manual carefully. In that we have no control over
the correct use, installation, application, or maintenance of our products, no liability shall be
st-prooffor all weather races.
assumed nor accepted for any damages, losses or costs resulting from the use of the product.
-in capacitor module.
ange calibration, easy to use.
FEATURES:
: Low voltage cut-off protection for Lipo or NiMH battery / Over-heat protection / Throttle signal
• Water-proof and dust-proof for all weather races.
• Small size with built-in capacitor module.
with the jumpers.
• Automatic throttle range calibration, easy to use.
• Multiple protections: Low voltage cut-off protection for Lipo or NiMH battery /
】 】
Over-heat protection / Throttle signal loss protection.
• Easily programmed with the jumpers.
WP-1040-BRUSHED
WP-1040-BRUSHED-Crawler& Boat *
SPECIFICATION
Forward: 40A / 180A
t
* There are 2 kinds of WP-1040-BRUSHED-Crawler& Boat speed controllers, one has 1 output
Backward: 20A / 90A
for 1 motor, and the other one has 2 outputs for 2 motors (2 motors work synchronously).
** The WP-860-DUAL BRUSHED has 2 outputs to drive 2 motors synchronously. When driving 2
1:10 on-road, off-road Buggy, Truggy, SCT
motors, the Turns of the motors need to be increased.
540 or 550 size motor ≥12T
Model
H
or RPM < 30000 @7.2V
540 or 550 size motor ≥18T
H
or RPM < 20000 @7.2V
Cont. / Burst Current
Fwd: 0.002 Ohm, Bwd: 0.004 Ohm
Input
2A/6V (Linear mode BEC)
WP-1040-BRUSHED: 46.5*34*28.5, 65g
Cars Applicable
WP-1040-BRUSHED-CRAWLER: 46.5*34*28.5, 70g
WP-1625-BRUSHED
2S Lipo or
WP-1625-BRUSHED-Crawler
5-6 cells NiMH
Motor
Forward: 25A / 100A
t
3S Lipo or
Limit
Backward: 25A / 100A
7-9 cells NiMH
2-3S Lipo, 5-9 Cells NiMH
Resistance
1:18 & 1:16 on-road, off-road
Built-in BEC
1:18 & 1:16 Crawler and Boat
280, 370 or 380 size motor
Dimension &
H
or RPM < 30000 @7.2V
Weight
280, 370 or 380 size motor
H
or RPM <20000 @7.2V
BEGIN TO USE
Not Available
MH
1. Connect the ESC, motor, receiver, battery and servo according to the following diagram:
Fwd: 0.003 Ohm, Bwd: 0.003 Ohm
"+" and "-" wires of the ESC are connected to the battery pack.
1A/6V(Linear mode BEC)
Attention: The incorrect polarity will damage the ESC immediately.
The control cable of the ESC (trio wires with black, red and white color) is connected to
34mm*24mm*14mm, 23.5g
the throttle channel of the receiver (Usually CH2). The "Motor +" and "Motor –" wires are
WP-1040-BRUSHED-Crawler& Boat speed controllers, one has 1 output for 1 motor, and the other
connected to ESC without any order.
2 motors (2 motors work synchronously).
If the motor runs in the opposite direction, please swap these two wire connections.
BRUSHED has 2 outputs to drive 2 motors synchronously. When driving 2 motors, the Turns of the
creased.
2. Set the Transmitter
Please set the "D/R", "EPA" and "ATL" to 100% for throttle channel (for transmitter without
LCD, please turn the knobs to the maximum value), and set the "TRIM" of the throttle channel
motor, receiver, battery and servo according to the following diagram
to 0 (for transmitter without LCD, please turn the TRIM knob to its neutral position).
For FutabaTM and the similar transmitters, the direction of throttle
the ESC are connected to the battery pack.
channel shall be set to "REV", while other radio systems shall be set to "NOR".
orrect polarity will damage the ESC immediately.
The "Fail Save" function of the radio system is strongly recommended to be activated. Please
make sure that the motor can be stopped when the "Fail Save" happens.
3. Throttle Range Setting (Throttle Range Calibration)
In order to make the ESC match the throttle range of different transmitters, the calibration of
the ESC is necessary.
To calibrate the ESC, please turn on the transmitter, keep throttle stick at its neutral position,
wait for 3 seconds to let the ESC execute self-test and automatic throttle calibration. When the
ESC is ready to run, a long beep sound is emitted from the motor.
Note: Please calibrate the throttle range again when using a new transmitter or changing the
settings of the neutral position of throttle channel, D/R, ATV, ATL or EPA parameters,otherwise
the ESC may not work properly.
BEEP SOUND AND LED STATUS
The Meaning of Beep Sound
• 1 short Beep: The battery is NiMH/NiCd
• 2 short Beeps: The battery is 2S Lipo
• 3 short Beeps: The battery is 3S Lipo
• 4 short Beeps: The battery is 4S Lipo
• 1 long Beep: Self-test and throttle calibration is OK, the ESC is ready to run
FTX Outback Hi-Rock Manual.indd 5
FTX Outback Hi-Rock Manual.indd 5
WP-1060-BRUSHED
Forward: 60A / 360A
Backward: 30A / 180A
2-3S Lipo, 5-9 Cells NiMH
1:10 Crawler, Tank &Boat
540 or 550 size motor ≥ 8T
WP-1040-BRUSHED
or RPM <45000 @7.2V
WP-1040-BRUSHED-Crawler & Boat *
540 or 550 size motor ≥13T
or RPM <30000 @7.2V
Forward: 40A / 180A
Backward: 20A / 90A
Fwd: 0.0008 Ohm, Bwd: 0.0016 Ohm
2-3S Lipo, 5-9 Cells NiMH
3A/6V (Switch mode BEC)
1:10 on-road, off-road Buggy, Truggy, SCT
36*30*18, 40g
1:10 Crawler, Tank & Boat
WP-860-DUAL BRUSHED
540 or 550 size motor ≥12T
or RPM < 30000 @7.2V
Forward: 60A / 360A
540 or 550 size motor ≥18T
Backward: 30A / 180A
or RPM < 20000 @7.2V
2-4S Lipo, 10-12 Cells NiMH
Fwd: 0.002 Ohm, Bwd: 0.004 Ohm
1:8 on-road, off-road, Buggy, Truggy, Monster
2A/6V (Linear mode BEC)
Crawler and Boat
540, 550 or 775 size motor ≥12T
WP-1040-BRUSHED: 46.5*34*28.5, 65g
or RPM < 30000 @7.2V
WP-1040-BRUSHED-CRAWLER: 46.5*34*28.5, 70g
540, 550 or 775 size motor ≥18T
or RPM <20000 @7.2V
540, 550 or 775 size motor ≥24T
or RPM <15000 @7.2V
Fwd: 0.001 Ohm, Bwd: 0.002 Ohm
3A/5V(Switch mode BEC)
46mm*36mm*26.3mm, 73g
SPEED CONTROL CONNECTION DIAGRAM
other radio systems shall be set to "NOR".
SET THE ESC
The "Fail Save" function of the radio system is strongly recommended to be activated. Please mak
can be stopped when the "Fail Save" happens.
The ESC is programmed by the jumpers
(Tweezers are recommended to plug and unplug the jumper).
3.
Throttle Range Setting (Throttle Range Calibration)
THROTTLE STICK POSITION
In order to make the ESC match the throttle range of different transmitters, the calibrationof the ESC
To calibrate the ESC, please turn on the transmitter, keep throttle stick at its neutral position, wait fo
Top point of forward
Neutral Point
ESC execute self-test and automatic throttle calibration. When the ESC is ready to run, a long b
from the motor.
Note: Please calibrate the throttle range again when using a new transmitter or changing the s
position of throttle channel, D/R, ATV, ATL or EPA parameters,otherwise the ESC may not work pro
【 【 BEEP SOUND AND LED STATUS】 】
The Meaning of Beep Sound
1 short Beep: The battery is NiMH/NiCd
2 short Beeps: The battery is 2S Lipo
3 short Beeps: The battery is 3S Lipo
4 short Beeps: The battery is 4S Lipo
1 long Beep: Self-test and throttle calibration is
OK, the ESC is ready to run
PROTECTION FUNCTIONS
User Manual of Water-Proof Brushed Speed Controller (RTR Version)
【 【 THROTTLE STICK POSITION】 】
【 【 SET THE ESC】 】
The ESC is programmed by the jumpers
(Tweezers is recommended to plug and unplug the jumper).
1. Low voltage Cut-off (LVC) protection: If the voltage of battery pack is lower than the
threshold for 2 seconds, the ESC will enter the protection mode.
When the car stops, the red LED blinks to indicate the low voltage cut-off protection has been
activated.
Table A: LVC protection for WP-1060-BRUSHED, WP-1040-
BRUSHED, WP-860-DUAL BRUSHED (F/B/R or F/B mode).
2S Lipo
3S Lipo
Output reduces 50%
Output reduces 50%
at 6.5V Output cuts
at 9.75V Output cuts
off at 6.0V, cannot be
off at 9.0V, cannot be
recovered
recovered
LED Status
【PROTECTION FUNCTIONS】
• When the throttle stick is in neutral range, red LED is off
1.
Low voltage Cut-off (LVC) protection: If the voltage of battery pack is lower tha
• Forward, brake or reverse at partial throttle, red LED blinks
• Forward, brake or reverse at full throttle, red LED is solid
ESC will enter the protection mode.
When the car stops, the red LED blinks to indicate the low voltage cut-off protect
Table A: LVC protection for WP-1060-BRUSHED, WP-1040-BRUSHED, WP-8
mode).
5
2S Lipo
Output reduces 50% at 6.5V
Output
cuts
off
at
6.0V,
Top point of backward
direction
direction
When the throttle stick is in neutral ran
Forward, brake or reverse at partial thr
Forward, brake or reverse at full throttl
4S Lipo
5-9 cells NiMH
Output reduces 50%
Output reduces 50%
at 13V Output cuts
at 4.5V Output cuts
off at 12V, cannot be
off at 4.0V, cannot be
recovered
recovered
3S Lipo
Output reduces 50% at 9.75V
18/12/2019 14:54
18/12/2019 14:54
Output cuts off at 9.0V, cannot
HW-SM690ENG-V3-20
The control ca
wires with black
is connected to
of the receiver
"Motor +" and
connected to E
If the motor r
direction, plea
wire connection
2.
Set the Tra
Please set the
"ATL" to 100%
(for transmitter
turn the knob
value), and se
throttle channe
without LCD, p
knob to its neut
For
Futaba
TM
transmitters, th
channel shall b
LED Status
4S Lipo
Output reduces 50% at
Output cuts off at 12V,
Publicité
