Aikan 4LPM Mode D'emploi page 6

suction tube to the unit to priming tube until paint
discharges from priming tube
"off" (9)
►
Remove the priming tube from the waste
bucket and clip to suction tube and submerge in
Switch power to "on" (16)
►
paint pail (18)
airless gun into waste bucket and pull trigger (11)
Turn "spray/prime" switch to "spray" mode and
►
continue to spray into waste bucket (19)
spraying If the motor stops, means that the pump
and tubes are primed
►
priming steps Start painting.
PAINT.
►
Before painting, ensure the the unit has been
primed and verify that nozzle tip is aligned properly
►
Remove or cover objects that you want to protect
from overspray and paint mist
adjust nozzle to "spray" setting (3)
at the lowest setting on the pressure control knob
and increase pressure as needed by turning
clockwise to create a good spray pattern (20)
►
Practice the painting techniques that follow on a
scrap workpiece before painting your workpiece.
PAINTING TECHNIQUES.
►
Before painting, ensure the the unit has been
primed and verify that nozzle tip is aligned properly
►
Keep the airless gun approximately 30 cm from
►
the surface Keep airless gun straight and move
arm across at a steady rate while staying 30 cm
from the surface (21)
or paint will be uneven (22)
by half, always aim stroke at bottom edge of last
stroke (23).
CLEARING AIRLESS GUN TIP.
► Occasionally, the airless gun tip will become
►
clogged with paint Follow these instructions to
►
clear airless gun tip
Adjust nozzle to "clean/eject" setting (4)
►
"spray/prime" switch to "spray" mode (19)
power to "on" (16)
►
Spray into waste bucket until
►
clog clears (11) Release trigger
to "spray" mode (3).
CLEANING.
Turn power off and turn "prime/spray" switch
►
to "prime" mode to relieve pressure (10)
►
Unthread airless gun tip and remove (24) (25)
► Relieve pressure and drain paint from tubes
►
(26) Separate tubes (12)
in empty waste bucket (13)
tube in water or flushing fluid (14)
unit and turn "on" power (16)
►
Switch power to
►
►
Stop
►
If it does not stop, repeat
►
Once primed,
►
Start spraying
►
Do not fan the airless gun
►
Overlap strokes
Switch power to "off" (9)
►
►
►
Adjust nozzle
►
Place priming tube
►
Submerge suction
►
Plug in the
►
The unit will start
pumping and water or flushing solvent as well
as air bubbles will be purged from system
fluids discharge from priming tube into waste
bucket until fluid is clear (27)
priming tube is clear, switch power to "off" (9)
Point
Turn "spray/prime" switch to "spray" mode (19)
►
Switch power to "on" (16)
►
►
(28) Change to waste bucket as paint thins
Turn "prime/ spray" switch to "prime" mode
►
(29)
►
(10) Continue to flush until clear (30)
trigger, turn power "off" and relieve pressure (9,
►
10, 11)
►
(31) Unscrew nut from housing, it is behind
the swivel connector (32)
►
Clean all parts in warm, soapy water or flushing
fluid with a bristled brush (34).
STORAGE.
►
When cleaning for long term storage (more
than 48 hours). it is important that the unit is not
stored with any water or water-based material left
in the pump, hose, tubes, or airless gun
will corrode the product
the the unit before storage
if not already removed (35)
and loosen the clamps from both tubes, then
disconnect tubes from the pump body (36)
about 30 mililitres of light household oil or a pump
storage product into each inlet (37)
spray" switch to "spray" (19)
control knob to "low pressure spray" (8)
rag over the paint hose outlet (38)
to "on" for five seconds, then turn the power to "off"
Turn "prime/spray" switch to "prime", this will
►
(39)
keep storage fluids in the unit (10)
tubes and secure with the clamps (40)
the unit with a clean cloth
location out of reach of children.
MAINTENANCE.
Turn
Turn ►
The airless electric equipment has been
designed for a long working life with minimum
maintenance
correct care of the airless electric equipment and
regular cleaning
unplug the airless electric equipment from the
power source before cleaning or performing any
maintenance
may be cleaned effectively using compressed
air after each use
available, use a brush to remove dust from the
airless electric equipment
vents and switch levers must be dept clean and
free of foreign matter
English 6
►
►
Paint into paint pail
Remove the trigger guard from housing
►
Remove filter (33)
►
Is very important clean
►
Remove paint hose
►
Turn the unit over
►
Turn pressure
►
Store in a clean dry
►
Optimum use depends on
►
To prevent accidents, always
►
The airless electric equipment
►
If compressed air is not
►
Motor ventilation
►
Do not attempt to clean
►
Let
After fluid in
►
Release
►
This
►
Add
Turn "prime/
►
►
Hold a
►
Switch power
►
Replace the
►
Wipe the