Aikan 4LPM Mode D'emploi page 4

►
simple cut Injection can lead to amputation
a physician immediately
of the type of coating material or cleaning agent
with which the injury was caused
operating range of this airless gun is 250 Bar fluid
►
pressure Never aim the airless gun at any part
►
of the body Never allow any part of the body to
touch the fluid stream
a leak in the fluid hose
►
the airless gun Gloves will not provide protection
against an injection injury
►
gun at anyone else
trigger, shut the pump off and release all pressure
before servicing, cleaning the tip or guard, changing
tip, or leaving unattended
released by turning off the motor
spray valve must be turned to prime to relieve the
►
pressure Refer to the pressure relief pressure
described in the pump manual
tip guard in place while spraying
provides some protection but is mainly a warning
►
device Always remove the spray tip before
flushing or cleaning the system
develop leaks from wear, kinking and abuse
can inject material into the skin
►
before each use Never use an airless gun without
a trigger lock and trigger guard in place and in good
►
working order All accessories must be rated at or
above the maximum operating pressure range of the
►
airless gun This includes spray tips, extensions
►
and hose Hazard: Explosion hazard due to
incompatible materials will cause severe injury or
►
property damage Do not use materials containing
►
bleach or chlorine Do not use halogenated
hydrocarbon solvents such as bleach, mildewcide,
methylene chloride trichloroethane
compatible with aluminum
material supplier about the compatibility of material
►
with aluminum Hazard: General
gun can cause severe injury or property damage
►
Read all instructions and safety precautions
before operating this airless gun
sources of ignition; eg open flames, cigarettes (also
cigars and pipes are sources of ignition), sparks,
hot wires and hot surfaces, etc
equipment when spraying
be provided with a protective mask
prevent work related illness, the manufacturer‟s
regulations for the materials, solvents, and
cleaning agents used must be observed when
preparing, working with and cleaning the airless
►
gun Protective clothing, gloves, eyewear, and, in
certain cases, protective skin cream are necessary
►
to protect the skin Follow the coating material and
solvent manufacturer‟s warnings and instructions
►
Inform the physician
►
The maximum
►
Do not allow body to touch
►
Never put hand in front of
►
Never point the airless
Always lock the airless gun
►
Pressure will not be
►
The prime/
►
Always keep the
►
The tip guard
►
The hose can
►
Inspect the hose
►
They are not
►
Contact your coating
►
This airless
►
Never spray near
►
Wear respiratory
►
The operator must
►
In order to
► ►
See Extraction equipment should be installed by the
user in accordance with local regulations
objects being sprayed must be earthed
each use, check all hoses for cuts, leaks, abrasion
or bulging of cover
movement of couplings
hose if any of these conditions exist
►
a hose
pressure hose
force to the hand that is holding the airless gun
►
The recoil force of the airless gun is particularly
powerful when the tip has been removed and a high
pressure has been set on the airless high-pressure
►
pump Therefore, when cleaning without tip set the
pressure control valve to the lowest pressure
only manufacturer authorized parts
all risks and liabilities when using parts that do not
meet the minimum specifications and safety devices
of the airless gun manufacturer
static-electricity discharge from the airless gun is
to be diverted to the grounded high-pressure pump
via the conductive high-pressure hose as stipulated
►
The maximum surface temperature corresponds
►
A leak to the permissible material temperature
the permissible ambient temperature can be found
in the technical data
of machine sparks, prevent impact stresses and
any work on the unit with tools in the explosion-
hazardous area.
RESIDUAL RISKS.
►
Residual risks are risks, which cannot be
excluded, even when equipment is used for the
intended purpose
areas of the actual residual risks will be pointed
out using warning and/or prohibition signs.
Risk Source / Cause Impact
Injection Atomized, high
injury pressure stream
of fluid
Explosion Static electricity
or fire or sparks
Hazaar- Hazaardous
dous vapors from spray
vapors material
DESCRIPTION OF THE PRODUCT.
►
The airless electric equipment has been designed
for the high pressure atomization of liquid coating
materials
with the airless electric equipment before use.
English 4
►
Check for damage or
►
Immediately replace the
Replace it with another grounded high-
►
Pulling the trigger causes a recoil
►
To avoid the generation
►
In such cases the applicable
Preventative
measures
Severe NEVER aim the
injury or gun at any part of
amputation the body
Severe Use well ventilated
injury area. Ground de
airless gun
Severe Use well ventilated
injury area. Use mask
►
Refer to this plan to familiarize yourself
►
The
►
Before
►
Never repair
►
Use
►
User assumes
►
Hazard: Any
►
This and
Can occur
during:
Setup,
operation
Operation
Operation