Table des Matières
Publicité
Contenu de l'emballage
Inspecter le contenu de la boîte du casque d'écoute stéréo
numérique sans fil. L'emballage doit contenir :
Casque d'écoute
Câble audio RCA (1)
8
Station d'accueil
Câble adaptateur
de 3,5 mm à RCA
Guide de l'utilisateur
Batteries
Adaptateur c.a.
rechargeables
(2)
RF-RBWHP01 Rocketboost Wireless Stereo Headphones
Package contents
Charging the headphones
you connect the same color jacks together (the white to the white and the red to the red).
Important
Note: If your audio source has only a 3.5 mm "phones" or "line out" jack, use the supplied 3.5 mm-to-RCA adapter
cable.
will guarantee a longer operating lifetime for the batteries.
make sure the batteries are fully charged for at least 16 hours. This
L L
R
AC power adapter
Rechargeable
1 Place the headphones onto the docking station. Make
Headphone
The audio input signal from the AUX INPUT jacks is
Headphones
batteries (2)
sure that the headphone charging contacts and the
charging
contact
connected to the AUX OUTPUT jacks. This is helpful if
back panel
Docking station
Docking station
docking station charging pins make contact.
your audio source component only has one audio
• The docking station charging indicator turns red to
Docking station charging pin
output and you want to connect it to both the
indicate the headphones are charging.
headphone and another component, like an audio
• When the headphones are fully charged (which
To do this, follow the steps in "To connect the docking
Audio cable
3.5 mm-to-RCA
Notes:
station to your audio source:, " then connect the second
adapter cable
Quick Setup Guide
supplied RCA audio cable from the aux output jacks of
RCA audio cables (2)
User Guide
(depending on the volume level you choose).
Caution
sure that you connect the same color jacks together (the white to the white and the red to the red).
Connecting the AC adapter to the docking station
connections.
Listening through the headphones
Caution
headphones. Make sure that the power supply outlet matches the AC adapter's 120V before making the
Turning on and pairing the headphones and the docking station
1 Set the headphones' volume level to the minimum.
2 Turn on the headphones and docking station. Make sure that your docking station and
connection.
1 Set the POWER switch on the left earpiece of headphones to ON. The HUB switch on the docking
headphones are wirelessly "joined. "
1 Connect the AC adapter connector to the docking station' s DC IN jack.
station should be set to ENABLE, so the power indicator should turn green.
The power indicators light steadily if the docking station and headphones are joined and blink
2 Connect the AC adapter plug to an AC power outlet. The STANDBY indicator lights red steadily
2 Press the POWER button on the docking station. The HUB switch on the docking station should
slowly if they are not. If they are not joined, see "Establishing Communication" in the User Guide.
when the docking station is plugged in.
3 Connect the AC power adapter to the sender/receiver and plug into an AC power outlet.
be set to ENABLE, so the power indicator should turn green.
3 Put your headphones on your head. Adjust the angles of the left and right ear pieces until you feel
Caution: Plug the AC adapter into the power outlet only after all other connections are completed.
The sender/receiver automatically turns on and the power indicator turns green.
comfortable.
Notes:
4 Turn on your audio source and begin playback.
If there are multiple sources in the Rocketboost network, press the
SOURCE button on the
Installing headphone batteries
• If the headphones' charge is low, the indicator turns red. Ifthis happens, the headphones should be charged.
• When the docking station is turned on, the TX indicator lights blue steadily.
is a hub) blinks several times, indicating that the current audio source is changing.
The headphones are powered by two AA rechargeable batteries. Each earpiece houses
Connecting the system to an audio source
5 Adjust the headphone volume to your normal listening level.
Notes:
one battery.
Caution: Continuous use at high volume may permanently damage your hearing.
•
Do not install non-rechargeable batteries.
In a typical user installation, the docking station is connected to the audio output of a TV. Other
devices with audio outputs could be used as well.
Note
•
Make sure that all batteries are installed correctly.
Note: Before you listen to the system after all connections
1 With an earpiece cushion facing you, unlock and remove
Audio source
Docking station
left and right earpiece cushions by slightly rotating them
back panel
1 Set the POWER ON/OFF switch located on the headphones' left earpiece to OFF.
clockwise, then pulling them away from the headphones.
To connect the docking station to your audio
2 Press and hold the POWER button on the docking station. The power indicator on the docking
2 Insert one AA rechargeable battery into each battery
compartment. Make sure to align the + and - symbols on the batteries with
source:
the symbols in the battery compartments.
Using the supplied RCA audio cable, connect the
3 Replace left and right cushions.
audio output jacks of your audio source to the AUX
RCA cable (supplied)
INPUT jacks of the docking station. Make sure that
QUICK SETUP GUIDE
Guide d'installation
rapide
Rocketboost network notes:
Every Rocketboost network must contain
at least one hub device, which helps
devices join the network. The network can
using the hub switch on the back of all
have only one hub, which you can enable
Rocketboost send
Rocketboost senders and
Rocketboost prod
sender/receivers.
Rocketboost product, you should make
this device the hu
this device the hub, if you already have
Rocketboost prod
hub mode on this device.
hub mode on this
Rocketboost products, you should disable
Important: Hub d
Important: Hub devices must always have
power for your ne
power for your network to operate. The
saving) mode, bu
hub device can b
saving) mode, but must stay plugged in.
hub device can be in standby (power-
ENGLISH 10-0801
USA 55423-3645
Publicité
Table des Matières
