Screen Research MMS2-L1 Manuel D'installation Et D'utilisateur page 8

ENGLISH - Screen user manual
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current and
Hz transformer installed.
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be
fitted with an omnipolar selector switch with contact opening distance of at least 3 mm. For the screen's control use only
the selector switch provided by manufacturer, or equivalent model. The selector switch must be mounted within sight
distance of the product, at a 1.5 - 1.8 m height from the floor.
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to
ensure the screen's optimal and unaltered performance over time. Prior to carrying out any operation on electrical parts
ensure that power supply is disconnected
Somfy 230V 50Hz
MOTOR
EU or UK or US
PLUG
Volt: 230V AC
Frequency: ~Hz50
Power: 90-120-140-160-240W
Motor
Torque: 6-10-15-20-30Nm
characteristics
Speed: 17-32RpM
Max no. of cycles: 2
Operating T°:
from –20 to +55 °C
WARNING - READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS
Adjustments shown must be performed by authorised and specialised personnel only. Incorrect performance of the procedures described may result in damages to the product which
will not be covered by guarantee. Adjustment is performed with a 4 mm hex wrench (included).
WARNING
End stop is adjusted so as to allow the projection sheet to wind around the roller at least 1.5 times to avoid the sheet coming loose. Special attention must be paid when end stops are
adjusted in such a way that projection sheet unwinds beyond the factory setting. Incorrect adjustment of end stops can cause:
-Projection sheet coming away from the roller
-Projection sheet winding the wrong way, with ensuing damage to flatness of the projection surface and to winding mechanisms
-Breaking of bottom end black frame welding (framed screens)
-Excessive strain on motor with possible ensuing damage and activation of motor's thermal resistance
-Excessive winding of the end stop adjustment system with ensuing breaking of the mechanical part
WARRANTY
Operators are reminded that in cases where seals have been tampered with and where any damages have resulted from incorrect adjustment, repair interventions shall not be covered by
guarantee.
PROJECTION FABRIC
-
Pushed the White and Yellow buttons for unlocked the end-stop positions.

- Move the projection fabric in the down end position, ATTENTION do not to exceed the limit
specified in the projection canvas and release the yellow button

- Move the projection fabric in the up end position and release the white button
Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE
Please verify that you are working with the latest revision of this document before specifying your screen.
Doc: MMS2-L1 Installation Manual rev2 | 03.02.2015 |Download at: www.screenresearch.com 2015 AdeoSreen All Rights Reserved.
All manuals and user guides at all-guides.com
09 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION
ELECTRICAL CONNECTION:
WARNING:
Somfy 120V 60Hz
US
Volt: 120V AC
Frequency: ~Hz60
Power: 80-110-180-210W
Torque: 6-10-15-25Nm
Speed: 14-17-38RpM
Max no. of cycles: 2
Operating T°:
from –20 to +55 °C
10 END STOP MOTOR ADJUSTMENT
END STOP MOTOR ADJUSTMENT SOMFY
The screens with motorization SOMFY are equipped with cables complete of
the switch for the surface movement and of Plug for connection to the
electricity. The screens and the cables, are included of quick connectors.
The screens with motorization
LUTRON are equipped with quick
connectors for connection to
transformers or management
systems LUTRON
Somfy 100V 50/60Hz Lutron QED
UK EU or UK or US
Volt: 100V AC Volt: 24V AC
Frequency: ~Hz50-60 Frequency: ~Hz50-60
Power: 80-160W Power: 27-37W
Torque: 10-20Nm Torque: 2.82-6.78 Nm
Speed: 12/14-17/20RpM Speed: 25mm/1sec
Max no. of cycles: 2 Max no. of cycles: 2
Operating T°: Operating T°:
from –20 to +55 °C from –20 to +55 °C
LATERAL MASK
-
Pushed the White and Yellow buttons for unlocked the end-stop positions.

- Move the projection fabric in the down end position, ATTENTION do not to exceed the limit
specified in the projection canvas and release the white button

- Move the projection fabric in the up end position and release the yellow button
Lutron QS
EU or UK or US
Volt: 24V AC
Frequency: ~Hz50-60
Power: 24-37W
Torque: 2.82-6.78 Nm
Speed: 25mm/1sec
Max no. of cycles: 2
Operating T°:
from –20 to +55 °C
Page 8