Lumina PERLA GARDEN 35 Instructions page 6

GB
Suspended light fi tting for general lighting, for both in- and outdoor use,
made of die-cast aluminium, a diffuser in polyethylene and a feeding wire
in neoprene. Possibility of cascaded installations (fi g. 5-6) since you can
electrically connect several fi ttings to the same power connection. Possi-
bility of vertical and horizontal adjustments by means of ropes and other
accessories of simple use. Many installation options are possible for one
or more fi ttings.
Lamping: E27 max 30W compact fl uorescent - max 60W halogen.
Degree of protection IP65.
NOTICE - INSTALLATION TIPS
The symbol recommends the minimum distance to be kept
from the lighted object.
In case of halogen lamp installing or replacement please use a self shield-
ed tungsten halogen lamp only
Warning: read and carefully follow this instruction: we recommend that a
specialized technician carries out this job.
Warning: always cut off the current prior to start any operations.
Warning: For serial wiring it is mandatory to comply with the European
Norms that prescribe the use of the components (feeding wires, cable
glands, cable clamps etc.) that are included in this package.
Warning: when connecting this fi tting to the main network for outdoor
use, use appropriate components (feeding wire, cable-clamps, junction-
boxes, plugs, etc.) with a minimum degree of protection of IP44, or more.
For model Perla Garden 35 M - code 861, use a cable H05RN-F 2x075, Ø
5,5 - 6,5 mm bearing the HAR mark of conformity.
Warning: maximum load for this power feeding system is 600W in case of
a cascaded installation down one only light point.
Warning: use hooks and dowels suitable to the kind of ceiling or wall, and
to the total weight of the fi ttings to be installed: Q.ty 1 Perla Garden 35 =
3,5kg. Consider wind motion in case of outdoor use.
Warning: for model Perla Garden 35 M - code 861, the use of sets code 820
(fi g.2) and code 821 (fi g.3) is recommended.
Warning: in case of horizontally tensioned mount, as shown in pict. 5 ,
we recommend the use of architectural steel cables (not included in this
package).
To clean the fi tting: never carry it out when the fi tting is still warm. Only
use neutral cleaning products.
INSTALLING OR REPLACING BULBS - MAINTENANCE
SINGLE MOUNT - Perla Garden 35 M (code 861)
(Fig.1) •From the side opposed to the feeding cable, remove the screws
(A) from the tap (B) with the Allen key included in box.
•Then remove the diffuser and carry out maintenance works (installing or
replacing the bulb, cleaning etc.).
•For ceiling or wall mount use hooks for dowels suitable to the weight of
this light fi tting (3,5kg) and to the kind of ceiling or wall.
(Fig. 7) •Thread the feeding wire through the cable-lead (O) and connect
it to the terminal, then tighten it by use of the cable-clamp inside the box
(P).
•Tighten the ring-nut of the cable-lead (O) fi rmly.
•After that put the diffuser at its place again and tighten the screws (A).
Warning: make sure that washers (C) are set correctly.
•Connect the feeding wire to the electric main network.
INSTALLING OR REPLACING BULBS - MAINTENANCE
SINGLE MOUNT - Perla Garden 35 (code 860)
(Fig.1) •From the side opposed to the feeding cable, remove the screws
(A) from the tap (B) with the Allen key included in box.
•Then remove the diffuser and carry out maintenance works (installing or
replacing the bulb, cleaning etc.).
•After that put the diffuser at its place again and tighten the screws (A).
Warning: make sure that washers (C) are set correctly.
INSTALLING - SUPPORTING ROPES
1) Mount the hooks (I) (fi g.3) or some other supports suitable to the kind
of ceiling or wall, and to the total weight of the composition to be in-
stalled.
2) Cut the ropes (D) to needed length (fi g. 2) (notice: wrap the cut end
with a tape), with slots as sketched, and close the two shells (E) screwing
the bolt (F) and the nut (G).
•Hook the carabiners (H) to the slots.
(fi g. 4) •Hook the carabiners (H) to the connection points (I) and to the
supports (L).
•Connect the feeding wire to the electric main network.
INSTALLATION WITH SERIAL FEEDING
(fi g. 4) •Place and hook all the fi ttings prior to carry out electrical connec-
tions, in order to correctly estimate the cable-lengths (always add 40 cm
to the distance between fi ttings).
•Hook the carabiners (H) to the connection points (C) and to the supports
(I).
We recommend to keep a 70 cm minimum distance between fi ttings.
If you fi nd the composition satisfactory, cut all the exceeding feeding ca-
bles.
.
Warning: do not exceed the maximum weight load: 50 kg.
•Unhook the fi ttings and lay them down (on ground or table) for an easier
electrical connection to each other. Notice: if the connection between fi t-
tings is made on the same side, just open the cover on the opposite side
for an easier bulb replacement and maintenance operations.
3) (fi g.1) Release the screws (A) by use of the Allen key included in box,
and shift the diffuser.
•Remove the cover (B), from the feeding or the other side according to
your intention about next fi tting entrance (fi g.7).
•Shift the diffuser and mount the lamp, put the diffuser at ist place again
but do not yet mount the cover .
4) (fi g.8) Release the bolt (M) by use of the box spanner/wrench (Q) in-
cluded in box, and remove the cap (N).
•Mount the cable-lead (O) included in box, together with all Its compo-
nents, as shown in picture.
•Thread the feeding wire through the cable-lead (O) and connect it to
the terminal, then tighten it by use of the cable-clamp inside the box (P).
Tighten the ring-nut of the cable-lead (O) fi rmly.
5) Proceed as per points 3 and 4 again to connect all the fi ttings to each
other.
(fi g.1) •Mount the sources, and tighten the screws (A) to set the diffuser.
Warning: make sure that washers (C) are set correctly.
6) Once the fi ttings are connected together as shown(fi g.8), you need the
help from one or more people to hook the system to the supports (I) that
you had previously mount to the walls or to the ceiling.
7) Connect the feeding wire to the electric main network.
MAINTENANCE AND LAMP REPLACEMENT
WITH SERIAL FEEDING
1) Hook the carabiners as shown in fi g.9. Or, otherwise, take a provisional
rope to hold as shown in fi g.9a, by-pass the operated globe and hook it
to the next fi tting to support the fi ttings below, holding it in slight tension.
2) See fi g.1. •From the side opposed to the feeding cable, remove the
screws (A) from the tap (B) with the Allen key included in box.
•Then remove the diffuser and carry out maintenance works (installing or
replacing the bulb, cleaning, etc.).
•After that put the glass-diffuser at its place again and tighten the screws
(A). Warning: make sure that washers (C) are set correctly.
Carefully read the instructions before assembling the light fi tting
which is guaranteed safe and reliable when it has been correctly in-
stalled and properly used. We recommend to conserve the
GUARANTEE This light fi tting is guaranteed under the conditions in force in
the Country of sale. For claims under guarantee, the sales receipt must be
shown.
REMARKS FOR A SAFE USE
The light fi tting that you have purchased has been designed and built
according to European security norms in force and is certifi ed by an
appointed Institute for Quality Marks.
The safe use of a light fi tting emboding high temperature
components requires, beyond the necessary attention, to carefully
follow these instructions:
Read carefully and conserve the instructions for the correct use of
the light fi tting.
We suggest to have the fi tting installed by a specialized technician.
Do not use the light fi tting for improper applications, that haven't been
foreseen in the project.
Do not use bulbs of higher power than the one specifi ed in the
instructions and on the labels sticked on the light fi tting.
When cleaning or changing the bulb of the light fi tting, remember to
previously unplug the same or switch off the main.
Let the light fi tting and the bulb cool down before touching it with the
hands.
Moreover, we suggest to remember:
Never clean the light fi tting when hot or under tension.
Never use fl ammable products to clean the light fi tting.
The glass components - bulb included - can break and therefore are
dangerous if uncarefully handled.
Light fi ttings should be installed out of the reach of children and in such
a position where they cannot be hit by anything.
Do not install the light fi tting too close to fl ammable materials (curtains,
etc.), nor cover it, to prevent the normal cooling.
Do not allow children to play with the fi tting.
In case of troubles, misworking or damage to the cable, contact your
Lumina dealer for checking and repairing.
instructions.