stayer HL 11B Instructions D'emploi page 18

gb
- Attach water supply hose (not supplied) to the mains
water supply and machine.Connecting high pressure
water supply hose/nozzle
- Securely screw high pressure hose 6 onto machine at
connection 12.
- Inserting the vario-jet/fan power lance 4 into the power
gun 3. Depress and turn the vario-jet/fan power lance
90°clockwise to lock in place.
ELECTRICAL CONNECTION
Your machine requires an earth connection. The operating
voltage is 230 V ac, 50 Hz (for non-EU countries 220 V,
240 V as applicable). Only use approved extension cables.
Contact your STAYER Service Centre for details. If you
want to use an extension cable when operating your high
pressure washer, only the following cable dimensions
should be used:
1.5 mm2 – max length 20 m
2.5 mm2 – max length 50 m
Note! If an extension cable is used it must be earthed
and connected through the plug to the earth cable of
your supply network in accordance with prescribed
safety regulations. If in doubt contact a qualified
electrician or the nearest STAYER Service Centre.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket must be
of watertight construction and intended for outdoor
use. Cable connections should be kept dry and off
ground.
For increased electrical safety touse a Residual Current
Device (RCD) with a tripping current of not more than 30
mA. Always check your RCD every time you use it.
For safety, it is essential that the mains plug attached
to the product is fitted to the power supply cable. The
couplings of connection leads must be protected
against splashes and
the coupling sockets on the leads must be made of
rubber or coated with rubber. Fixing means for the
connection leads must be used. If the supply cord is
damaged, it must be replaced by a STAYER Service
Centre.
ILLUSTRATED DESCRIPTION
1
Trigger safety lock
2 Trigger
3 Power gun
4
Vario-jet-fan power lance
5 Main switch
6 Water inlet hose
7
Inlet connector
8 Detergent nozzle and bottle
9 Roto power lance
10 Detergent Tank
11 Take water outlet
12 Fitting connections
13 Strainer
3. OPERATING INSTRUCTIONS
If the machine looks bad or parts are missing, do not
connect it and take it to the technical service. Do not use the
machine without understanding and applying this manual.
ENGLISH
18
PLACEMENT AND TESTING
Connect the product to the mains supply ensuring that the
mains switch is in the
Open water tap
Press the safety lock 1 to release the trigger 2. Fully press
the trigger 2 until there is a constant flow of water to clear
the air from the machine and water supply hose. Release
trigger 2. Press the trigger safety lock 1.
Press button on main switch 5.
Point the power gun 3 downwards. Press the trigger safety
lock to release the trigger 2. Fully press the trigger 2.
Stopping
Release trigger 2. Press the trigger safety lock. The power
gun is now locked and can not be operated accidentally.
Press button on the main switch 5.
Close water tap. Unplug the machine from the electric
supply. Press the trigger safety lock 1 to release the trigger
2. Fully press the trigger 2 until there is no more water
pressure in the machine. Release trigger 2. Press the
trigger safety lock 1. Disconnect water supply hose from
machine and water supply.
Fine-tuning operations
Vario-jet-fan power lance
Twist the front ring to adjust from a pencil to a fan jet and
vice versa.
INSTRUCTIONS FOR USE
General
Ensure that the machine is on level ground. Do not
overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the
machine to become unstable and fall over. Do not kink or
drive a motor vehicle over the high pressure hose. Do not
expose the high pressure hose to sharp edges or corners.
Never use the roto nozzle to clean motor vehicles.
Operating with Detergents
Only use approved detergents. Unsuitable detergents
may damage the unit and the object being cleaned.
Fill the detergent tank 10 with detergent, dilute as
recommended. To spray detergent move vario-jet-fan
power lance to low pressure mode. We recommend that
you use detergent sparingly for the sake of the environment.
Observe the recommended dilution on the detergent label.
Recommended cleaning method
Step 1: Loosening dirt
Spray on detergent sparingly and allow to react for a short
time.
Step 2: Removing dirt
Spray off the loosened dirt with the high-pressure spray.
Note! When cleaning a vertical surface spray off dirt/
detergent from the bottom and work in an upwards
direction. Rinse from the top and work downwards.
4. MAINTENANCE INSTRUCTIONS
CLEANING, MAINTAINING, LUBRICATING,
SHARPENING
Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or
entangled.
18
position.